Solve the following problems.1. A pipe bends through an angle of 90° in the vertical plane. At the inlet it has a cross-sectional area of 0.003 m and a gauge pressure of 500 KPa. At exit it has an area of0.001 m2 and a gauge pressure of 200 KPa. Calculate the vertical and horizontal forcesdue to the pressure only.2. Calculate the momentum force on a 180° bend that carries 5 kg/s of water. The pipe is500 mm bore diameter throughout. The density is 1000 kg/m2.

1. A pipe bends through an angle of 90° in the vertical plane. At the inlet it has a cross- sectional area of 0.003 m and a gauge pressure of 500 KPa. At exit it has an area of 0.001 m and a gauge pressure of 200 KPa. Calculate the vertical and horizontal forces due to the pressure only. 2. Calculate the momentum force on a 180° bend that carries 5 kg/s of water. The pipe is 500 mm bore diameter throughout. The density is 1000 kg/m.

1. A pipe bends through an angle of 90° in the vertical plane. At the inlet it has a cross- sectional area of 0.003 m and a gauge pressure of 500 KPa. At exit it has an area of 0.001 m and a gauge pressure of 200 KPa. Calculate the vertical and horizontal forces due to the pressure only. 2. Calculate the momentum force on a 180° bend that carries 5 kg/s of water. The pipe is 500 mm bore diameter throughout. The density is 1000 kg/m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

mache
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
Good day. I require assistance as this will help in my examination review. (Basic Aerodyn Principles) Consider the wind tunnel shown below. The diameter at section 1 is 0.8 m and the diameter at section 2 is 0.5 m. A manometer is used to determine the pressure difference between the two sections. The manometer liquid has a specific gravity of 0.82. Determine the change in height in the manometer if the velocity at section 2 is 72 m/s. Assume incompressible flow and standard sea-level conditions. Provide answer in centimeters. Round-off answer to the nearest whole number. **Would gladly appreciate an explanation. Thank you.
Consider the bend shown in . The total mass of the bend and the water within it is 20 kg, with a mass center at point G. The pressure of the water at A is 50 kPa Assume that no force is transferred to the flanges at A and B. Suppose the velocity through the pipe to be 4.5 m/s. 100 mm By 60 100 mm 600 mm 150 mm- 100 mm D Part A Determine the horizontal component of force exerted on the fixed support D. Express your answer to three significant figures and include the appropriate units.
If anyone can help with this problem I would appreciate it. Thank you!
Write the difference between linear and angular momentum.
Water flows in a D = 36 mm diameter pipe as shown in the figure. Since Q = 60 m3 / h, and the density of %3D water is 1000 kg / m³, calculate the resultant force on the elbow and the angle it makes with the horizontal. 120°
b) Figure Q3 shows a vehicle uses water scooping to slow down. The scoop is 3-m wide. Draw the free body diagram of the scoop. Determine the amount of force exerted on the scoop. If the force exerted by the flow to the scoop is 460 kN, determine the velocity of the vehicle. The vehicle scoops off 10 cm of water.
Water flows steadily up the vertical 1-in.-diameter pipe and out the nozzle, which is 0.5 in. in diameter, discharging to atmospheric pressure. The stream velocity at the nozzle exit must be 30 ft/s. Calculate the minimum gage pressure required at section 1 . If the device were inverted, calculate the required minimum pressure at section 1 to maintain the nozzle exit velocity at 30ft/s?
Water under a gauge pressure of 350 kPa flows with a velocity of 5m/s through a right- angle bend that has a uniform diameter of 250mm. The bend lies in a horizontal plane and water enters from the west and leaves towards the north. Assuming no drop in pressure, what is the magnitude and direction of the resultant force acting on the bend?
A tank (contains a fluid of density=2715.2 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s D 4 m- 35 deg Do = 4 cm Cable
The diameter of a pipe gradually reduces from 1 m to 0.7 m. The pressure intensity atthe center line of 1 m section is 8and rate of flow of water through the pipe is600 liters/s.,I. Find the intensity of pressure at the center line of 0.7 m section.II. Determine the force exerted by flowing water on transition of the pipe.