A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from the nozzle, it falls and strikes a vane attached to another cart. Neglect the friction effect. i. Compute the velocity of water leaving the tank Vi and water velocity leaving the cart V2. ii. Deterime the tensions in the rope A and the rope B. Nozzle area = 0.01 m? 2 m Horizontal free jets 4 m Rope A Rope B

A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from the nozzle, it falls and strikes a vane attached to another cart. Neglect the friction effect. i. Compute the velocity of water leaving the tank Vi and water velocity leaving the cart V2. ii. Deterime the tensions in the rope A and the rope B. Nozzle area = 0.01 m? 2 m Horizontal free jets 4 m Rope A Rope B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The front and side views of a centrifugal impeller are shown in the figure below. All symbols have…

A: The outer radius of the impeller = r2 =0.4 m d2 = 0.8 m The blade height at impeller outlet b2 =…

Q: The centrifugal pump shown in Figure Q2 is delivering water from Tank A to Tank B. The distance…

A: Given:L=8.5 mDischarge pipe diameter, D2=200 mm=0.2 mSuction pipe diameter, D1=300 mm=0.3 mDischarge…

Q: 5. A nozzle that discharges a 60-mm-diameter water jet into the air is on the right end of a…

A: To determine:the magnitude and direction of the resultant axial force.Given:The outlet diameter of…

Q: 2. Oil (sg=0.90) is flowing at 150 L/min through a turbine. The pressure before the turbine is 750…

A: The flow rate of oil is Q=150 l/min. The specific density is SG=0.9. The pressure before the turbine…

Q: 6.66 PLUS This nozzle bends the flow from vertically upward to 30° with the horizontal and…

A: Step 1:

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

Q: (Moment-of-momentum) A lawn sprinkler is constructed from pipe with 0.226-in. inside diameter as…

A: d=.226 in=.0188ft r1=r2=5.54 in=.462 ftr=2.77 in =.231 Since diameter is same and mass flow rate is…

Q: The air flow through a jet engine is 30 kg/s and the fuel flow is 1 kg/s. The exhaust gases leave…

A: Given Data ma =30kg/s mf =1kg/s Ve =610m/s f=1.12x106 w

Q: An irrigation pump delivers water through a 6 - inches horizontal pipe flowing full at the outlet,…

A: If an object travels with constant velocity, then the motion of the object is said to be uniform…

Q: Flow direction 581 N 759 N 625 N 874 N 811 N 679 N 723 N

A: Given data m˙ = 30 kg/s mass of water in elbow = 50 kg D = 13 cm d = 6 cm θ = 45o β = 1.03 To…

Q: In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target…

Q: 1a. Water flows into a tee fitting at a flow rate of 0.02 m3 /s. A pipe is connected to B. The…

Q: 18 |A vertical jet of water impinges on a horizontal disk as shown. The disk assembly mass is 30 kg.…

A: Given mass of thde disk m=30kgU=5m/sh=3mV=15m/sA=0.005m2

Q: Patm A water Tank C hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in…

Q: could you please help me calculate the maximum height of the jet , Hj in metres please

Q: 2. The figure shows a pipe reducing section that is bolted on to the end of a pipe. Water flows…

Q: data apply: Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s. At the exit, V2 is purely axial…

Question

100%

A tank is connected with cart by the rope A as shown in figure. When the water leaves the
tank from the nozzle, it falls and strikes a vane attached to another cart. Neglect the friction
effect.
i. Compute the velocity of water leaving the tank V1 and water velocity leaving the cart V2.
ii. Deterime the tensions in the rope A and the rope B.
Nozzle area = 0.01 m?
2 m
Horizontal free jets
4 m
Rope A
Rope B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 5.2 A simple air duct with a side exhaust is shown below along with the direction of the velocity vectors at each inlet or outlet. The cross-sectional area at 1 and 3 are identical, Ac1 = Ac3 = 0.5 m². The velocity at 2, V₂, makes a 20° angle with the opening in the side of the duct A₂ = 0.5 m². Measurements indicate that the flow is steady with velocities V₁ = 10 m/s and V3 = 3 m/s. Assume that air behaves like an incompressible substance under these conditions. a) Determine the ratio of the volumetric flow rate at 2 to the volumetric flow rate at 1, /. b) Determine the ratio of the velocity at 2 to the velocity at 1, V₂/V₁. 1 20° Ans: a) 0.65 ≤ / ≤ 0.81 b) 1.75 ≤ V₂/V₁₂ ≤ 2.10
Use inlet and outlet velocity triangle please show all work to find the the power
Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4 identical jets spaced equally around the rim of a disc. Water enters though a hollow shaft and then flows radially out to the jets. The nozzle of the jet has a diameter D of 0.3 cm and makes an angle a = I (3 with the horizontal plane of the disc(See figure). The jets are oriented so that v2r=0. If the total flowrate Q=50 mL/s and the disc has radius R= 7.5 cm, determine the torque in dyne-cm required to keep the disc from rotating. Water jet R. Water flows radially inside dise to jet Water in View from top View from side
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height at the impeller outlet b2 = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.3 m³/s. The outlet blade angle 3₂ = 31 degrees and the impeller rotational speed w = 1400 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The impeller power is ß₂ kW. Front View ra @ b2- → Side View
Q6) A water jet hits horizontally a 50-kg block with a velocity of (20 m/s), see the figure. The friction coefficient between the block and the ground is (0.9). What is the minimum diameter (d) of the water jet required for the block to slide to the left?
A static thrust stands as it showed in the Figure. The intake velocity is 200 m/s, exhaust velocity is 500 m/s, intake cross-section area 1 m, intake pressure is -22.5 kPa, and exhaust pressure is pressure and considered zero. Determine the anchoring force (Fth).( Density = 1.02kg / (m ^ 3))
A fire starts in an apartment building in downtown Boston. When the firefighters arrive, they immediately get to work putting out the fire using a fire hose. The water for the fire hose is provided by a fire hydrant at ground level. Assume that the velocity of the liquid coming from the fire hydrant is 1.6 m/s, and that the pressure at the hose nozzle is atmospheric pressure (101000 Pa). a. The firefighters start with the ground floor, so there is no change in height between the fire hydrant and the hose nozzle. If the velocity of the water coming out of the nozzle is 12.8 m/s, find the pressure at the fire hydrant in units of Pa. b. After the ground floor fire is put out, another fire is spotted on another floor. A firefighter carrying the hose is lifted on a platform to the same height as the fire, which is 44.35 m above the ground. Assuming that the pressure found in part a) remains constant, what would be the new velocity of the water coming out of the nozzle at this new height?
answer fast
PLEASE FOLLOW THE INSTRUCTION AND TRY TO ANSWER CORREVTLY. PLEASE ANSWER QUICKLY . THANKS
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height the impeller outlet b₂ = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.5 m³/s. The outlet blade angle 3₂ = 35 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The gravitational acceleration g = 9.81 m/s². The theoretical (Euler) head is m. Front View P₂1 r2 b2- 118 Side View
Water flows out of 5 mm x 200 mm slots in a sprinkler as shown. The mass flow rate is 15 kg/s. 200 mm 250 mm a. Find the torque required to prevent the sprinkler from rotating. b. Find the rotation rate of the frictionless sprinkler when released.
Q3. A free jet of water with an initial diameter of 2 in strikes the vane as shown in the figure below. Given that = 30 °. and V₁ = 100 ft/s. Owing to the friction losses, assume V₂ = 95 ft/s. Flows occurs in a horizontal plane. Find the resultant force on the blade. V₁ CV Fy F