1. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress In the tube when the power is transmlt- ted through a 4 :1 gearing. [Ans. 30 MPa]

1. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress In the tube when the power is transmlt- ted through a 4 :1 gearing. [Ans. 30 MPa]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compound steel [G = 83 GPa] shaft consists of a solid 58-mm-diameter segment (1) and a solid 31-mm-diameter segment (2). The allowable shear stress of the steel is 67 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to Pc ≤ 4.1°. Assume L₁=1.1 m and L₂=2.0 m. Determine the magnitude of the largest torque To that may be applied at C. L₁ (1) Answer: Tc= 372.89 (2) L2 N-m. Tc с
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m
Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of "T" Nm. ii) Bending moment of "M?' Nm.
Please don't provide handwritten solution...
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
Please include given and PDF THANK YOU
2) A hollow tube constructed of metal is subjected to five torques acting in the directions shown in the figure. The tube has an outside diameter of 1.0 in. The allowable shear stress is 12,000 psi. The shear modulus is 9500 ksi. The length between AB, BC, CD and DE is 2ft. a) Draw the internal torque diagram for the shaft using the rules we discussed in class. Based on the allowable shear stress, design the inner diameter of the shaft in inches. b) c) Using your answer from part (b), calculate the total rotation between points A and C in radians. Be sure to track which direction each portion of the shaft is rotating. T₁= TB = T, = Tc= 1000 lb-in. 500 lb-in. 800 lb-in. 500 lb-in. A B D d₂ = 1.0 in. T₂= 800 lb-in. E
i need the answer quickly
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A steel shaft in the form of a solid body circular rod or a circular tubecan be manufactured. The shaft is required to bear 1200 N.m of torsional torque. Anti-shear stress for shaft material 40 MPa, largest permissible unit torsion angle in the rod 0.75 ^ 0As / m and steel's shear modulus is G = 78 GPa;a) Find the required diameter d0 for a solid circular shaft.b) Find the required outer diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and the weight ratio for ring cross section and solid section shafts. please solve carefully and in detail thank you
6. Please solve carefully/ellaborately, include the units and draw the diagram. Your works will be appreciated much, Thanks!
2. [-/1 Points] DETAILS GGMECHMAT9 3.7.006. The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm (see figure). 2,300 гpm 80 mm 25 mm 80 mm (a) If the shaft transmits 150 kW, what is the maximum shear stress in the shaft? (Enter the magnitude in MPa.) MPа (b) If the allowable shear stress is 30 MPa, what is the maximum power (in kW) that can be transmitted? kW