The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm (see figure). 2,300 rpm 80 mm 25 mm 80 mm (a) If the shaft transmits 150 kW, what is the maximum shear stress in the shaft? (Enter the magnitude in MPa.) MPa (b) If the allowable shear stress is 30 MPa, what is the maximum power (in kW) that can be transmitted? kW

The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm (see figure). 2,300 rpm 80 mm 25 mm 80 mm (a) If the shaft transmits 150 kW, what is the maximum shear stress in the shaft? (Enter the magnitude in MPa.) MPa (b) If the allowable shear stress is 30 MPa, what is the maximum power (in kW) that can be transmitted? kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure below, A 50 mm shaft is subjected to a reversed load P = 2700 N. Find the length (L), if the stress at the fillet equal to the stress at the center. 6.25mm 2700N 2700N 62.5 s0 375 Fillet Center Fillet All Dimensions in mm
A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional area of 4350 mm². Since tem = 50 MPa and G = 77.2 GPa, find the maximum applicable torque T.
A hollow steel shaft used in a construction auger has outer diameter d2 = 7.8 in. and inner diameter d1 = 5.5 in. (see figure). The steel has shear modulus of elasticity G = 11.5 x 10^6 psi. For an applied torque of 175 k-in. , determine the following quantities:a.) Shear stess T2 at the outer surface of the shaftb.) Shear stress T1 at the inner surfacec.) rate of twist Θ (degrees per unit of length)
The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of the shaft is mm3. The polar modulus of shaft (in mm³)
Two forces, 100 kN and 200 kN, act on the rectangular column in the figure. Find the stresses at A and B points according to the given and show them on the stress element.
Q2/A compound shaft shown in the figure is subjected to a torque TC = 7500 N.m at C and restrained by a support at A. Segment (1) is a solid brass [G1 = 5800 GPa] shaft with an allowable shear stress of τ1 = 38 MPa. Segment (2) is a solid aluminum [G2 = 4000 GPa] shaft with an allowable shear stressof τ2 = 69 MPa. [L1= 0.7 m, L2= 0.5 m] Determine the minimum required diameter of the brass shaft (1)?in mm Determine the minimum required diameter of the aluminum shaft (2)?
مقاومة المواد
50 MPа 60 100 MPa For the stress conditions given in the figure; a) Draw the Mohr Circle. b) Find the principal stress values and their directions and show them on the figure. c) Find the normal and shear stresses on the C plane and show the point corresponding to this plane on the Mohr circle.
Q2: Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of active turns. (b) Find the spring rate. Assume the material is A228 music wire. (c) Find the force F, required to close the spring solid. (d) Find the shear stress in the spring due to the force F,. 120 mm M 3.4 mm 50 mm
(BB) Q1: The shaft, as shown in Fig. is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 2.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable shear stress for the shaft material is 85 MPa. Taking torsion and bending factors as 1.25 and 1.5 respectively, find the shaft diameter. C # -100- A B -150-100 D TB2 All dimensions in mm. B A TAZ TAI TB1
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 43 Hz. If the shaft transmits 156 kW, what is the maximum shear stress in the shaft in MPa?
Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure , Determine the angle of rotation at the free end. D2 D1 T (kN-m) Given: L(m) T(KN-m) D1 (mm) 02 (mm) G (GPa) 28 60 140 120