A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q=5 kN/m for AB span; and is constant with q=5 kN/m for BC span. The Young's modulus of steel is 200 GPa. y, v a 5 mm 200 mm 300 mm b с

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given data: FS=2.2σfail=614  MPa Need to determine the allowable stress for member σallow.

Q: For the simply supported beam subjected to the loading shown, sketch the shear force diagram.…

A:

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.2 * 10 ^ 5 * N and the…

A: The problem is asking for the minimum wall thickness of a pipe that can withstand a certain axial…

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

A:

Q: The 0.91-in.-diameter rod in (Figure 1) is subjected to the loads shown. Figure 9 in. 200 lb 300 lb…

A:

Q: Determine the shear and moment as functions of position. (Round the final answers to four decimal…

A: This question is based on the concept of SFD and BMD

Q: In the image below, B and C are pulleys. The belts on the pulleys exert the forces shown in the…

A:

Q: A beam is shown in the figure below. Part A If M = 1 kip/ft, determine the resultant force the…

A: To Find : The resultant force and bending moment on the top board A of the beam, Given : The moment…

Q: What steps should be taken to obtain The resultant internal loadings at a point located on the…

A: The internal loading are the forces and the moments that are applied by the half of the section on…

Q: For the beam and loading shown, determine the maximum normal stress due to bending on section a-a.…

A:

Q: If the allowable bending stresses for a beam in one application is 6 kip/in² in tension. The…

A: Given data:- Beam section=W8×40 Allowable bending stress (σ)=6 kip/in2 To find:-Allowable maximum…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Determine the largest permissible value of P for the beam and loading shown, knowing that the…

A:

Q: *1-4. Determine the resultant internal loadings in the beam at cross sections through points D and…

A: Take section BC: take the moment about point B: ΣMB=0RC×16-16×8=0RC=8 kipand RB+RC=16 kipRB=16-8=8…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.