1. A cylindrical specimen of a metal object with a radius of 3.8E-2 m and a gaugelength of 20.31 mm is pulled in tension. Use the load-elongation characteristicstabulated below to answer the following questions;Load Length(N)(mm)0620.3120.3820.4520.5120.551218243020.613620.6442.8 20.6848.920.7255.2 20.7660 20.7965.8 20.8470.7 20.8777.3 20.9383.1 20.9888.6 22.1591.58 23.2491.68 25.41ChangeinlengthLength (x10-2 m) (m)Computed strain Computed stress (N/m²)

Given data:- The given radius, R=3.8×10-2 m The given original length, L=2.031×10-2 m The given…

1. A cylindrical specimen of a metal object with a radius of 3.8E-2 m and a gauge length of 20.31 mm is pulled in tension. Use the load-elongation characteristics tabulated below to answer the following questions; Load Length (N) (mm) 0 20.31 6 20.38 12 20.45 18 20.51 24 20.55 30 20.61 36 20.64 42.8 20.68 48.9 20.72 55.2 20.76 20.79 60 65.8 20.84 70.7 20.87 77.3 20.93 83.1 20.98 88.6 22.15 91.58 23.24 91.68 25.41 Change in length Length (x102 m) (m) Computed strain Computed stress (N/m²)

1. A cylindrical specimen of a metal object with a radius of 3.8E-2 m and a gauge length of 20.31 mm is pulled in tension. Use the load-elongation characteristics tabulated below to answer the following questions; Load Length (N) (mm) 0 20.31 6 20.38 12 20.45 18 20.51 24 20.55 30 20.61 36 20.64 42.8 20.68 48.9 20.72 55.2 20.76 20.79 60 65.8 20.84 70.7 20.87 77.3 20.93 83.1 20.98 88.6 22.15 91.58 23.24 91.68 25.41 Change in length Length (x102 m) (m) Computed strain Computed stress (N/m²)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

* Question Completion Status: 5 6 OL Distributed load, w = 1.10 MN/m ag, h = 42 Distance, a = 34 7 The cable supports a railway bridge between two tunnels. Given: 9 a 10B What is the maximum tension (MN) in the cable? Express your answer in 2 decimal place. 12 13 150 160 17 18 19 20
The following figure shows a simple bracket made of structural steel with Young's modulus E = 200 GPa and Poisson's ratio v = 0.3. The bracket has a cross-section profile shown below and an extrusion depth of 12 cm. A through-hole of diameter 1.5 cm is centered on the bracket's flat ends, one on each side, as shown in the figure. Suppose that the bracket is fixed on the bottom, and lifted by a pressure load of 1,296.12 N/cm² from the inside surface of the top flat portion. What is the total deformation of the bracket in mm? 10.000 1.500 1.500 R3.000 8.000 1.500 12.000 1.500 8.000 All dimensions are in centimeters. 1.500
Problem 5
9
Show complete solution.
Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at the lower end. Find the instantaneous stress induced in the bar and its corresponding extension when a weight of 150 N falls on the collar from a height of 60 mm. What percentage error in the stress induced will result if extension of the bar is neglected. Take E 2x 105 N/mm².
The hammer of an impact testing machine weighs 120 lbs. As shown in figure , it is attached to the end of a light rod 5 feet long which is pivoted to a horizontal axis at A.
Must include the free body diagram. Urgent
A rectangular steel bar, which is of 2.8 m long and 15 mm thick, is subjected to an axial tensile load of 40 kN. If width of the bar varies from 75 mm at one end to 30 mm at the end, then what is the extension of the bar if E = 2 x 106 N/mm²?