* Question Completion Status:56OLDistributed load, w = 1.10 MN/mag, h = 42Distance, a = 347The cable supports a railway bridge between two tunnels.Given:9a10BWhat is the maximum tension (MN) in the cable?Express your answer in 2 decimal place.12 13150 1601718 19 20

Solution: Free body diagram of the given cable: Total length of the span, l = 34+34=68 m,

Question Completion Status: 5 6 a The cable supports a railway bridge between two tunnels. Given: Distributed load, w = 1.10 MN/m Sag, h = 42 Distance, a = 34 7 8 9 a What is the maximum tension (MN) in the cable? Express your answer in 2 decimal place. 12 13 17

Question Completion Status: 5 6 a The cable supports a railway bridge between two tunnels. Given: Distributed load, w = 1.10 MN/m Sag, h = 42 Distance, a = 34 7 8 9 a What is the maximum tension (MN) in the cable? Express your answer in 2 decimal place. 12 13 17

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two steel cables are fixed at points A and B and have a force acting at the union point C. To…

A: A frame is given, we need to find out the force in member AC and BC

Q: The figure shown is a chain weighing 2.5kg/m and suspended between two points on the same level 18m…

Q: Determine the tension developed in cables AB, AC, and AD. WRITE YOUR ANSWER IN TWO DECIMAL PLACES. D…

Q: Q1. A homogenous 2000 N bar AB is supported at either end by a cable as shown in figure. Calculate…

Q: If the weight of the block shown is 90kN and to be located at the center of gravity G. What is the…

Q: A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of…

A: Given data: Length of cantilever beam=4m Outer dia=45 mm Inner dia=35 mm Allowable stress=150 Mpa…

Q: The truss, used to support a balcony, is subjected to the loading shown. Approximate each joint as a…

Q: A wire of uniform material weighing 0.32 lb. per cubic Inch hangs between two points 120 ft. apart…

A: From the above information, we have calculated the required unknown. First, we have to calculate the…

Q: ve the following problems: 1. Determine the force in each bar of the truss shown in figure caused by…

A: The load is lifted at constant velocity, the forces involve is similar to forces under static…

Q: The truss is made from A992 steel rods each having a diameter of 0.9 in .(Figure 1) Part A Determine…

A: The FBD of the truss will be: Now the forces in each member :

Q: The three cables are used to support the 50-kg flowerpot (Figure 1) Figure o 15m HE Determine the…

Q: The following beam is pin connected at point A and held by cable BDE. The beam supports a 80 kg mass…

Q: y 150 mm 150 mm B 400 mm 600 mm A

Q: The rigid diaphragm shown below has the following rigidities: Wall 10' 10 VBUD Rigidity 3 3 2 A…

A: Torsional moment - 550 kip-ft To find- Forces in each wall and rigidity.

Q: A homogenous 800 kg. bar AB is supported at either end by a cable shown in the figure below.…

A: Given Mass 800 kgSpan 10 mStresses in steel and bronze are 120 and 90 MPaTo find out Area

Q: A rigid bar AD is hanged by two steel cables of diameter 0.065 in as shown in the figure. Find: a)…

Q: A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed…

A: L=50m E=200GPa Po= 10kg w=0.05kg/m

Q: 2. A truss of span 10 meters is loaded as shown in Fig. 13.19. Find the forces in all the members of…

A: To Find Forces in all the members of the given Truss.

Q: The hoist shown is used in a machine shop to position heavy workpieces in a lathe. If the cable…

A: Given :

Q: 3. The roof truss is subjected to the loadings shown. Determine the force in each member and…

A: Determine the force in each member and indicate if the members are in tension or compression.

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm². ▼ Part…

A: Given:Cross sectional area = To find:The magnitude P

Q: The beam is subjected to a shear of V = 34 kN. Set 300 mm Part A 20 mm A 20 mm Determine the web's…

A: Given: The shear force in the beam is 34 kN. Consider the figure.

Q: A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed…

A: The given values are as follow,Length(L)=50mE=200GPaPo=10kgw=0.05kg/mTo determine The normal…

Q: he loading acting on the beam (Figure 1) by a single orce. Suppose that F₁ = 500 N, F₂ = 340 N, and…

Q: The metal plate is held by two cables as shown in the following figure. If the force of each cable…

A: Lets find out the forces in component forms, for that first find out the unit vectors in the…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

Q: Proble A weight of 100 Ib is supported by two ropes as shown. Calculate the tension in each rope…

A: W=120lb To find tension in rope CA and CB

Q: A rigid bar AD is hanged by two steel cables of diameter 0.065 in as shown in the figure. Find: a)…

Q: 1. The plate is horizontal, is in equlibrium, and weighs 1450 N. Determine the tension in cables AB,…

A: The given figure is shown below:

Q: A floor system in a small building consists of wood planks supported by 2 in. (nominal width) joists…

Q: A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter…

Q: For the truss shown in the figure, estimate the horizontal displacement at joint H. The area (A) and…

Q: The velocity ratio between the bigger and the smaller branched pipes is

Q: A uniform bar AB weighing 500 kg is supported at both end by cable as shown in the figure below.…

Q: Give me sample problem on cables carrying concentrated load.. Show how to solve the support…

A: Solution: Consider a basic parabolic cable with a span as L and with a deflection or dip at the…

Q: The man attempts to pull down the tre- and small pulley arrangement shown tension in AB is 55 lb and…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

T:39)
A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter table. Find the tension in the 3 cables. @ 080 2021 Cathy Zupke parameter L₁ L₂ L3 L4 M B value 4 1 2 8 10 M C units m m m m kg The tension in cable AB is 0 The tension in cable BC is 202 The tension in cable BD is Z -1₂- XN XN N y
A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter table. Find the tension in the 3 cables. L4 A cc 080 BY NO SA 2021 Cathy Zupke B parameter value 4 1 2 8 10 L₁ L₂ L3 L4 M The tension in cable AB is The tension in cable BC is The tension in cable BD is M C units |εεεε m m m m kg Z N N IN y
can you write the answer please
A homogeneous bar AB is supported at either end by a cable as shown in the figure. Calculate the largest allowable weight (kg) of the bar if the stress of each cable is not to exceed 90 MPa in bronze and 120 MPa in steel. The sizes of the cables are 28 mm Ø for Bronze and 20 mm Ø for Steel.
What is the diameter required?
The unit of the 3 given values are in MPa
No card B a Ó O00 n O O N 74 )| 10:11 < May 11, 2021 10:10 PM A bent rod has a diameter of d315 mm and is subjected to a force of P= 600 N. What is the normal stress developed at point A? * (2 Points) -120 mm- -120 mm- A 60 mm P P Share Favourite Edit Delete More ... 白

The beam is subjected to a shear of V = 34 kN. Set 300 mm Part A 20 mm A 20 mm Determine the web's shear stress at A. V Express your answer to three significant figures and include appropriate units. 400 mm 20 mm ? w = 200 mm 3.02 MPa Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining
The three cables are used to support the 50-kg flowerpot (Figure 1) Figure Um a HE <1 of 1 Determine the force developed in cable AB for equilibrium Express your answer to three significant figures and include the appropriate units. FAN= Value Submit Resvest Answer Part B Determine the force developed in cable AC for equilibrium Express your answer to three significant figures and include the appropriate units FAC Value Units ← PE Units P Pearson Copyright © 2022 Pearson Education Inc. All rights reserved. | Terms of Use | Privacy Policy Permissions Contacts I ? 14°C AB 4 de ENG M UK 11/10/2022
Solve the trusses using joint method include all tabulated summary of answers.
Two forces of magnitude TA = 6159 kips and TC = 7180 kips are applied as shown to a welded connection. Knowing that the connection is in equilibrium and angle X is 43.9°, determine the magnitude (kips) of TB . Round off only on the final answer