A wooden beam is loaded by a concentrated load P = 2000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that LAB = 2100 mm, LBC = 2900 mm, Bo=10 mm, B₁ = 20 mm, and H=240 mm, h=200 mm, h₁ =20 mm, determine the following quantities below:

A wooden beam is loaded by a concentrated load P = 2000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that LAB = 2100 mm, LBC = 2900 mm, Bo=10 mm, B₁ = 20 mm, and H=240 mm, h=200 mm, h₁ =20 mm, determine the following quantities below:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam AE is subjected to two concentrated forces P. As shown in the figure below, the flexural stiffness of the beam section is constant EI:At this time, if the concentration force F is increased to make the point C in the beam return to the center line (to offset the vertical displacement), what is the magnitude of the rigid concentration force?
A steel rectangular block, a = 2.4cm wide and b = 1.2 cm deep, is subjected to an axial tensile load as shown in the figure. Measurements show the block to increase in length by x=7.11×10-5m (initial length=10cm) and to decrease width by 8 z = 0.533×10-5m, when P is 45 kN. Calculate the modulus of elasticity and Poisson's ratio for the material. P
The steel block shown in Figure is subjected to a compressive force on all directions. Determine the change in length of Y-direction if the change in length of Z- direction is (-1.3mm). E for steel =210*10° N/mm? and u=0.28). 10em Sem
In the figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3mm. Draw the FBD and deformation diagram.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
Problem #2 The bar shown below has uniform cross section and material properties throughout. In addition to the loads shown, the bar experiences a uniform temperature change of AT = 75.4 °F. Given the x displacement at A is equal to -0.2044 inches determine the magnitude of the external load P. Report your answer in kips to 2 decimal places. D 7.5 ft C 1.7P 4.5 ft B 2.3P 2.5 ft A 3.1P E 29,000 ksi a = 6.5 x 10-6 1/°F A = 0.1 in2
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
mechanics of deformable bodies
QUESTION 4: Check whether the beam section whose loading condition, cross section and dimensions are given in the figure is sufficient. Also draw the shear stress diagram of the section next to the section.
* Your answer is incorrect. A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v= 0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad= i -0.21 L mm
An elastic cube prism has dimension of a=200 mm is placed in two rigid plates as shown in the figure. When the compression force of P= 1200 kN is applied on the direction of y axis of given cube, determine the volumetric strain.
The lower ends of the three bars in the figure are rigid homogeneous W = at the same level before the 100 kN block is attached. The temperature of the bars is then increased by 80°c. The block is assumed to remain horizontal after all deformations have occurred. The properties of the bars are shown in the table. STEEL BRÖNZE Length, L Area, A Modulus of Elasticity, E Coefficient of Thermal Expansion, a 1.0 m 1.6 m 500 mm2 900 mm? 200 GPa 83 GPa 11.7x10-6 mm/ (mm-°c) 18x10-6 mm/ (mm-°C) Calculate the stress developed in the bronze bar. Bronze Steel Steel A Calculate the stress developed in the steel bar. FIGURE 10