The state of stress at a point with respect to the XYZ coordinates system is given by stress matrix. Determine the normal stress and the magnitude and direction of the shear stress on a surface intersecting the point is parallel to the plane given by the equations 4X + Y + 3Z = 11. 15 10 10 10 -10 10 0 0 -40

The state of stress at a point with respect to the XYZ coordinates system is given by stress matrix. Determine the normal stress and the magnitude and direction of the shear stress on a surface intersecting the point is parallel to the plane given by the equations 4X + Y + 3Z = 11. 15 10 10 10 -10 10 0 0 -40

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the shear stress at points A and B on the beam if it is subjected to ashear force of V = 400 kN. Represent the state of stress on a volume element of these points.
Represent the stress state on a 2-dimensional square element, given the Mohr circle below. (a) Determine the maximum shear stress. (b) Determine the maximum and minimum principal stresses. (c) Planes on which the greatest shear stress and principal stresses act are square other than the square element. Show the elements by drawing.
Problem 3.4 The stress tensor has components at point P in ksi units as specified by the matrix 3 -6 [tij] = 3 6. 9. -6 -6 Determine: (a) the stress vector on the plane at P whose normal vector is 1 n = (êj + 4ế2 + 8ế3) , (b) the magnitude of this stress vector, (c) the component of the stress vector in the direction of the normal, (d) the angle in degrees between the stress vector and the normal.
Mechanics Of solids.
Solve it correctly using the equations
PLEASE ANSWER ASAP TY! SEE THE FIGURE SHOWN a) What is the shear stress component (τ) on a plane at 35o counterclockwise from the x-plane (in MPa)? Include negative sign if it will cause counterclockwise rotation. b) Determine the angle of inclination of the principal planes in the differential element (in degrees). Include negative sign for clockwise rotational sense. c) Determine the minor principal stress σ2 (in MPa). Include negative sign if compressive. d) What is the normal stress component (σ) on a plane at 35o counterclockwise from the x-plane (in MPa)? Include negative sign if compressive. e) What is the magnitude of maximum shear stress (in MPa)?
The state of stress at a point with ox, oy, and txy as shown. Analyze the state of stress at the point using the Mohr's circle of stress. Determine the following a) Principal stress, b) Maximum in-plane shear stress and c) Normal stress on the plane defined by x' axis where the angle is 25 degrees. Ne To 0. ox x TEV
Question 2 The stress acting on two planes at a point is indicated in Fig. 2. Determine using the stress transformation equations: a) the shear stress on plane a- a and sketch the orientation of the element with the relevant stress components. b) the principal stresses at the point (sketch of orientation of the element in principal direction not required). Hint: Associate plane b - b with the x - y and plane a - a with the x'-y' coordinate system. b [MPa] 80 Ta 90° 45° 60 60° b Figure 2: plane stress state
Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
The state of stress at a point with respect to a 0x₁x₂x, coordinate system is given by 1 3 2 3 1 0 20 2] What are the stress components with respect to axes Oxxx; which are obtained from the first by a 45° rotation (positive counterclockwise) about the X3 axis
(Problems No. 1- 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the normal stress at the y-axis 60 MPa 20 MPа 90 MPа O a. 75.60 MPa O b. -24.60 MPa 69.8 MPa O d. -39.8MPA
(Problems No. 1- 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the normal stress at the x-axis 60 MPa 20 MPa 90 MPa O a. 75.25 MPa b. -39,8 MPa 69.8 MPa O d. -24.60 MPa