Question 2 The stress acting on two planes at a point is indicated in Fig. 2. Determine using the stress transformation equations: a) the shear stress on plane a- a and sketch the orientation of the element with the relevant stress components. b) the principal stresses at the point (sketch of orientation of the element in principal direction not required). Hint: Associate plane b - b with the x - y and plane a - a with the x'-y' coordinate system. b [MPa] 80 Ta 90°

Question 2 The stress acting on two planes at a point is indicated in Fig. 2. Determine using the stress transformation equations: a) the shear stress on plane a- a and sketch the orientation of the element with the relevant stress components. b) the principal stresses at the point (sketch of orientation of the element in principal direction not required). Hint: Associate plane b - b with the x - y and plane a - a with the x'-y' coordinate system. b [MPa] 80 Ta 90°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Represent the stress state on a 2-dimensional square element, given the Mohr circle below. (a) Determine the maximum shear stress. (b) Determine the maximum and minimum principal stresses. (c) Planes on which the greatest shear stress and principal stresses act are square other than the square element. Show the elements by drawing.
Young modulus and stress have same dimension. a.True b.false
4
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 480 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Please do part 2 and 3 thank you
What is Mohr's circle of stress? At a point in an elastic material, a direct tensile stress of 60 kN/mm² and a direct compressive stress of 40 kN/mm² are applied on planes at right angles to each other. If the maximum principal stresses are limited to 75 N/mm² (tensile). Find the shear stress that may be allowed on the planes. Also determine the minimum principal stress and the maximum shear stress. 10001
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.18 in. In segment (2), the normal strain is measured as 1,650 pin/in. Assume L₁ - 34 in. and L₂-83 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) Answers: (a) in.& (b) = 4 i B (2) 4₂ in, pin/in.