Answered: 1) Write an instruction sequence to…

1) Write an instruction sequence to decrement the contents of data memory locations 0x10, 0x1 1, and 0x12 by 5, 3, and 1, respectively

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Assume the register ($s1) contains (0x87654321). Write at most two instructions to move ONLY the second byte value in the register ($s1) into the data memory at address stored in ($s0). Hint: In this problem, the second byte value in the register ($s1) = "0x43"
Assume that a memory is initialised as follows: Memory Address Cell Contents 0x000336 0x38 0x000337 0x26 0x000338 0x48 0x000339 0x38 0x00C33A 0x00C33B 0x77 0x38 The following sequence of operations is executed in the given memory: Write(0x00C337, 0x0205) Write (0x00C339, 0x0106) Write(0x00C338, 0x0109) Assume that the read and write operations are done in groups of two bytes, and the system is a big endian system. What is the result of read(0x00C337) +read (0x00C338)? Write your answer in Base 10 (decimal)
What is the effective address that is targeted by the store instruction whose code word in binary is:101011 01000 10001 1111 1111 1111 1100Assume [$t0]=0x400C
Use the following data declarations. Assume that the offset of byte Val is 00000000: .data byte Val sbyte 1,2,3.-7h word Val word 1000h.2000h 3000h, 4000h dwordVal dword 34567890h, 90785634h, 1234674Sh Show the value of the final destination operand after each of the following code fragments has executed: (If any instructions is invalid, indicate "INV" as the answer and briefly explain why) a. moy di 2 mov al, byte Val[di] b. mov bx, word Val mov esi, offset wordVal+4 xchg bx, [esi] R c. movsx cx, byte Val+3 d. mov ax, word ptr [dwordVal mov bl. byte ptr [dwordVal +10] e. mov al, 80h number add al 40h signed ;signed number answer al-= answer bx= answer (show your answer in binary) CX- answer |esi= answer bl= SF=
x = 4 and x = 8 **** and 3X is a two digit number, consider memory storage of a 64-bit word stored at memory word 3X in a byte-addressable memory (a) What is the byte address of memory word 3X? (b) What are the byte addresses that memory word 3X spans? (c) Draw the number 0XF1234567890ABCDE stored at word 3X in both big-endian and little-endian machines. Clearly label the byte address corresponding to each data byte value
3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, 50, s1 t1, so, s1 t2, so, s1 t3, 50, 51 addi t4, 50, 0x210 wwwwwww andi t5, 50, -16 add and or xor slli t6, 50, 12 srai s2, 50, 8 Dest. reg. in 8 hexadecimal digits
52-Two word wide unsigned integers are stored at the physical memory addresses 00A00 and 00A02, respectively. Write an instruction sequence that computes and stores their sum, difference, product, and quotient. Store these results at consecutive memory locations starting at physical address 00A 10 in memory. To obtain the difference , subtract the integer at 00A02 from the integer at 00A00. For the division divide the integer at 00A00 by the integer at 00A02. Use the register indirect relative addressing mode to store the various results.
I 1:If the hexadecimal value 0xF0A2 is a two’s complement, halfword value, what would it be in base ten. A.28,836 B.61,602 C.-28,836 D.-3,934 E.3,934 2:Choose the best statement describing the difference between the instruction is 32 bits wide and the instruction can process a 32-bit data. A. The instruction can process a 32-bit data means the instruction can do operation for many types of data bit length. B. The instruction is 32 bits wide means it can manipulate 32-bit data only. C. No different between both statements. D. The instruction is 32 bits wide means two memory locations are needed to store the instruction. E. The instruction is 32 bits wide means the instructions when it is converted to machine code, its length (size) is 32 bits.
Generate MIPS code for the following code segments assuming that all variables are in memory locations. clear steps
Consider the following code sequence, (i) MOV. B, R0 ADD C, R0 MOV R0, A Calculate the cost of the above instructions in terms of access time and memory usages
Microprocessors Fundamentals ENT 237 Homework 2 Problem1: Assume that register (D)= 3AHE and (E)=20Hex . Write an assembly language program to do the following: Load register A with data AAHEX. Copy this data to memory location 2800. Copy the content of memory location 3A20 to register B. Copy this data to register C. Copy data from register C to memory location 2801.
Select an OR instruction that will:a) OR BL with AH and save the result in AH.b) OR 88H with CX.c) OR DX with SI and save the result in SI.d) OR 1122H with BP.e) OR the data addressed by BX with CX and save the result in memory.f) OR the data stored 40 bytes after the location addressed by BP with AL and save the result in AL.