3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, so, s1 t1, so, s1 t2, so, s1 t3, s0, s1 addi t4, s0, 0x210 andi t5, s0, -16 slli t6, s0, 12 srai s2, 50, 8 add and or xor Dest. reg. in 8 hexadecimal digits

3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, so, s1 t1, so, s1 t2, so, s1 t3, s0, s1 addi t4, s0, 0x210 andi t5, s0, -16 slli t6, s0, 12 srai s2, 50, 8 add and or xor Dest. reg. in 8 hexadecimal digits

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Q3. Provide the hexadecimal representation of the following instruction.-- sd x17, 61 (x30) Ans:
Suppose the address of the first instruction is COAF3410 in hexadecimal in the following code. Show in decimal the immediate value (i.e. offset) in the beq and bne instruction, and in hexadecimal (of 7 digits) the psedudo address in the j instruction. Separate the numbers by comma. labell: beq $t1, st2, label3 (72 instructions here) label2: bne $13, st4, label1 (49 instructions here) labe 13: label2
QI) If BX=1000, DS=0200, SS=0100, CS-0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H, AL. Find the physical address in the memory. Q2) For the above question, if BP is used instead of BX, what is the physical address in the memory?
The addition or subtraction must be performed in HEX or BIN and can NOT be performed in DEC since those numbers represent signed OR unsigned values (These instructions are NOT executed one after the other one; instead, each instruction starts with the initial conditions given in the statement.) (a) 0x92394103 + 0xA04230C8 (b) 0x12345678 – 0xEDCBA988
H\W: assume Ds- 2400, show the content of register as each the following instruction execute Mov Bx, 1357, Mov SI, 1234. ES DI, (Bx) (SI]
Fill in the following table showing the results of the indicated instructions, using the register values shown. Also, show the OF and CF values AFTER the instruction executes. Show all results in hexadecimal. Show OF and CF as 0 or 1. Instruction %cl %al Result (in hex) OF CF 1. addb %al, %cl Ox52 Ox4D 2. addb %al, %cl Ох54 Ох67 3. addb %al, %cl OX9A OXD5 4. addb %al, %cl Ох95 OXBE 5. addb %al, %cl OXC4 Оx47 6. addb %al, %cl Ox9F OX7E 7. addb %al, %cl Ox24 Ox5B 8. addb %al, %cl Ox45 Ox3
ASSEMBLY The ROR instruction is only suitable for signed integers. True False
construct the program for our imaginary computer! There must be made of at least 5 instructions There should be at least 3 different types of instructions (write, move, decrement, add, or)
Fill in the following table showing the results of the indicated instructions, using the register values shown. Also, show the OF and CF values AFTER the instruction executes. Show all results in hexadecimal. Show OF and CF as 0 or 1. Instruction 1. addb %al, %cl 2. addb%al, %cl 3. addb %al, %cl 4. addb %al, %cl 5. addb%al, %cl 6. addb %al, %cl 7. addb %al, %cl 8. addb %al, %cl %cl %al Result (in hex) 0x52 0x4D 0x54 0x67 0x9A OxD5 0x95 OxBE OxC4 0x47 0x9F 0x7E 0x24 0x58 0x45 0x3 OF CF
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Assembly Language
Given the machine code, identify the instruction line or command line. Use CAPITAL LETTERS . No spaces in the operand side. NO need to include "H" for any immediate or displacement value. e.g. MOV AX,BX GIVEN: 10101001 10101100 00111011