Show the code to perform the computation X=A + (B + C) *D + E using microprocessors whichuse the instruction formats shown below. Each microprocessor has ADD and MUL instructions in itsinstruction set. Do not modify the values of A, B, C, D and E. If necessary, use temporary location Tto store intermediate results.a) 3-operand instructionsb) 2-operand instructionsc) 1-operand instructionsd) 0-operand instructions

Show the code to perform the computation X=4 + (B + C) *D + E using microprocessors which use the instruction formats shown below. Each microprocessor has ADD and MUL instructions in its instruction set. Do not modify the values of 4, B. C, D and E. If necessary, use temporary location T to store intermediate results. a) 3-operand instructions b) 2-operand instructions c) 1-operand instructions d) 0-operand instructions

Show the code to perform the computation X=4 + (B + C) *D + E using microprocessors which use the instruction formats shown below. Each microprocessor has ADD and MUL instructions in its instruction set. Do not modify the values of 4, B. C, D and E. If necessary, use temporary location T to store intermediate results. a) 3-operand instructions b) 2-operand instructions c) 1-operand instructions d) 0-operand instructions

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

a. Use the Vertical Microarchitecture Instructions set (provided in the handout) and write a microprogram, with a minimum number of instructions, to realize the following user-level instructions E:- C- (A 2) -1; GO TO 30. You may use an extra register if needed. * note: write the instructions in the table shown in part b'/ b. Show the Hexadecimal representation for each instruction field resulted from the solution in part a. Add more rows if needed. INSTRUCTION OP R1 R2 Edit Vimer Incert Format Tonls Table
Please solve and show all work. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: f = (g+i+2) + (h − 8); B[8] = A[i-9] + A[j+8] + 7;
Convert the given hex value to its R-format MIPS instruction by completing the following table. The instruction and letters for registers must be in lower case. DO NOT TYPE DOLLAR SIGNS WITH REGISTERS. Hex Opcode (decimal) rs (decimal) rt (decimal) rd (decimal) funct (decimal) Instruction 02488822 O 18 16 17 34 sub s4 $$1 " $ to " LA
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, 50, s1 t1, so, s1 t2, so, s1 t3, 50, 51 addi t4, 50, 0x210 wwwwwww andi t5, 50, -16 add and or xor slli t6, 50, 12 srai s2, 50, 8 Dest. reg. in 8 hexadecimal digits
Assume AL= 0FH, Set the fifth bit (D4) of the register AL. (D4=1) (HINT:Use one line instruction to perform the following action. ) Microprocessor
In this case, every instruction receives its own data, independent of how the data for other instructions is obtained. We make advantage of a: A Multiple Data/Instruction B Multiple Iterations of Data or Instruction C Singular Data Single Inst D Singe Inst Multiple
1) For each of the instructions below, assume the initial conditions shown for r3-r5 and the flags. For each instruction, show the value of any registers that are changed. If the instruction affects flags, show the value for all flags that are affected. Initial conditions: r3 = 0XF0E1 D2B3 r4 = 0x1496 3A40 r5 = 0×47CE 811E NZCV = 1010 a) ADCS r4,r3,r4 b) CMP r3,r5 c) TST r4,#0xF d) MVNS r5,r3 e) ASRS r3, r3, #1
The description of three-address instructions species the components of each type of instruction, but it does not specify the representation of these instructions in a data structure. Write the three – address code for the following expressions:(i) a = b * −c + b * −C(ii) A = −B * (C + D)(iii) (4 * 7 + 1) * 2(iv) a * - (b + c)
The execution of an instructions includes the following stages : instruction fetch, instruction decode, register fetch, ALU operation, memory operation, and write back. The analysis is based on an implementation of the datapath and control unit of a 32-bit MIPS microarchitecture.
Consider the following code sequence, (i) MOV. B, R0 ADD C, R0 MOV R0, A Calculate the cost of the above instructions in terms of access time and memory usages