LIST P = 16F877A Using INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed

LIST P = 16F877A Using INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed

Name: LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modu
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.

C++ Programming: From Problem Analysis to Program Design

8th Edition

ISBN:9781337102087

Author:D. S. Malik

Publisher:D. S. Malik

Chapter18: Stacks And Queues

Section: Chapter Questions

Problem 11SA

See similar textbooks

Similar questions

Use the following data declarations: .data byte Val word Val sbyte 1, 2, 3, FCh word 1000h, 2000h, 3000h, 4000h dwordVal dword 34567890h, 90785634h, 0Ah, 33445566h Show the value of the final destination operand after each of the following code fragments has executed: (If any instruction/s is invalid, indicate "INV" as the answer and briefly explain why) a. mov bh,byteVal+2 b. mov edx,1 C. add dx,[wordVal+4] mov ecx,5 xchg ecx,[dwordVal+12] d. mov ah, byte Val+3 sub ah,[ byte Val+0] sub ah,[ byte Val +2] e. mov eax, dword ptr dwordVal+7 f. movsx cx,byteVal+3 answer bh= answer edx= answer ecx= answer ah= answer eax= answer (show your answer in binary) CX=
Assignment for Computer Architecture! this is about hamming codes write the code IN MIPS ASSEMBLY LANGUAGE calculating hamming codes; The key to the Hamming Code is the use of extra parity bits to allow the identification of a single error. Create the code word as follows: Mark all bit positions that are powers of two as parity bits. (positions 1, 2, 4, 8, 16, 32, 64, etc.) All other bit positions are for the data to be encoded. (positions 3, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15, 17, etc.) Each parity bit calculates the parity for some of the bits in the code word. The position of the parity bit determines the sequence of bits that it alternately checks and skips.Position 1: check 1 bit, skip 1 bit, check 1 bit, skip 1 bit, etc. (1,3,5,7,9,11,13,15,...)Position 2: check 2 bits, skip 2 bits, check 2 bits, skip 2 bits, etc. (2,3,6,7,10,11,14,15,...)Position 4: check 4 bits, skip 4 bits, check 4 bits, skip 4 bits, etc. (4,5,6,7,12,13,14,15,20,21,22,23,...)Position 8: check 8 bits,…
2.- If the binary code for LOAD is (0011), for ADD is (0010), for STORE is (0110), for JMP is (0001) and for END is (0111). Assuming a 16 bits format, write the object code (binary representation) of the following program: Note: use 4 bits for the op-code and 12 bits for the ADDR.
MOV AL, 5 ADD AL, 4 The flag register is affected by the above addition and the carry flag will equal * to 1 MOV AL,OF5H ADD AL,OBH After the addition AL will contain FF BB 00 11 IK
NAND2TETRIS HARDWARE SIMULATOR HiLoMux - This has one 8-bit input bus, in, and one 4-bit output bus, out. Alsopresent is a sel input, which is used to select what appears on out. Ifsel is false, then out should contain the lower 4-bits of in (i.e. in[0],in[1], in[2], in[3]). If sel is true, then out should contain theupper 4-bits of in (i.e. in[4] mapped to out[0], in[5], mapped toout[1], etc.). In other words, the HiLoMux can be used to select anibble from a byte please use the skeleton program below CHIP HiLoMux{ IN in[8], sel; OUT out[4]; PARTS: }
• In string operations, register -- - is used to point to the source operand and register ----- is used to point to the destination operand. The-----flag is used to tell the CPU whether to or -- - the pointer in string operation. Your answer
NO PSEUDOINSTRUCTIONS you can not use li or la. Write a MIPS assembly language subroutine called GetCode that asks the user to enter a 7 bit code consisting of ones and zeros. When the user is finished entering the data, they should hit the Enter key. The data should be stored in memory as a NULL terminated ASCII string at the address passed into the routine in register a1. The user should be prompted for the data by displaying a prompt to the console asking them to enter the data. These prompts can be stored in the beginning of the data segment, and should not reside outside of the range 0x10000000 through 0x1000FFFF in memory NO PSUEDOINSTRUCTIONS
C++ Program: Make a program that would demonstrate the concept of Line Coding: Polar NRZ: Remember: if next bit is 1, there is inversion if next bit is 0, no inversion neg – means the signal is in the negative axis pos – means the signal is in the positive axis inv – means there is inversion no inv – means there is no inversion a. initially high (starts with positive, inverse is negative) Input: 1 1 1 0 0 1 0 1 1 0 0 0 Output: inv neg inv pos inv neg no inv neg no inv neg inv pos no inv pos inv neg inv pos no inv pos no inv pos no inv pos b. initially low (starts with negative, inverse is positive) Input: 1 1 1 0 0 1 0 1 1 0 0 0 Output: inv pos inv neg inv pos no inv pos no inv pos inv neg no inv neg inv pos inv neg no inv neg no inv neg no inv neg The logic here is when input is 1, next inputted 1 will be inverse…
Please answer part D only
the direction in hexadecimal of the last llvation in this memory is
Topic: Assembly Language Write a program called bit_check.asm that jumps to a label if either bit 4, 5, or 6 is set in the BL register. If these bits are set the program should print "Bits 4, 5, or 6 are set." followed by a new line character. If they are not set, jump to a label to print "Bits 4, 5, and 6 are not set." followed by a new line character. There should be 4 tests, test with each bit position set and with none of them set. Use the print_string procedure to print your output. Remember, you can jump to the exit label from anywhere in your program.
B1