Answered: Determine the memory location of…

Determine the memory location of operand 2 of the following instructions: a) MOV AL, [0100] b) MOV CL, [BX + 0200] Assume CS = 2300, BX = 1000H, SI = 0100

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Related questions

Q: Task: Convert the character in AL to upper case.

A: GIVEN: Convert the character in AI to uppercase.

Q: In the following instruction sequence, show the value of AL for each line of code. Write the value…

A: Instructions Value of AL(H) MOV AL, 01100001B AND AL, 00011101B 1H MOV AL, 12H MOV AL,…

Q: Select an XOR instruction that will: a) XOR BH with AH and save the result in AH. b) XOR 99H with…

A: a) XOR AH,BH b) XRI CL,99H c) XOR DX,DI

Q: State whether the following instructions are valid or not. If valid then define properly, if not,…

A: GIVEN: State whether the following instructions are valid or not. If valid then define properly, if…

Q: Please provide the binary and hexadecimal representation of following instruction: sw Sx1 8(Sx0)

A: 7) given instruction is sw $t1, 32($t2) is a I - type instruction as it is in the format shown below…

Q: Given a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selected…

A: Given instruction: mov R0 , [R1 + 1000] , store content of (R1 +1000) to register R0 [R1 +…

Q: st two bytes of a 2M x 16 bits main memory have the following Hex values:…

A: The first two bytes of a 2M x 16 bits main memory have the following Hex values:…

Q: The instruction that is not possible among the following is a) MOV AX, BX b) MOV AX, [BX]. c) MOV…

A: Question. The instruction that is not possible among the following is a) MOV AX, BX b) MOV AX,…

Q: 10. The number of clockcycles that take to wait until the length of the instruction is known in…

A: RISC processor: RISC processors use simple instructions that can be executed within one clock…

Q: Microprocessor (AVR) Fundamentals 1) - Find the contents of register R20 after each of the following…

A: As per policy three subparts can be solved once.

Q: 1. Describe the operation performed by each of the instructions that follow: d) CMP [0100 H] , AL e)…

A: Dear Student, In reality CMP compares two values by binary subtracting second passed value from…

Q: Encode the following instruction from MSP430 assembly to MSP430 machine code. Write the bytes in the…

A: Introduction Encode the following instruction from MSP430 assembly to MSP430 machine code. Write the…

Q: LIST P = 16F877A Using INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the…

A: PWM exploitation PIC Microcontroller The basics of pulse dimension modulation and you furthermore…

Q: Translate the following MIPS code to C. Assume that the variables f, g, h, i, and j are assigned to…

A: In the C code in step 2:int *A and int *B are declared as pointers to integers to represent arrays A…

Q: QI) I BX=1000, DS-0200, SS=0100, CS-0300 and AL=EDH, for the following instruction: MOV [BX] +…

A: Here is Solution for Above Problem :: Q1). Given Data : BX = 1000 DS = 0200 SS = 0100 CS = 0300 AL…

Q: H\W: assume Ds- 2400, show the content of register as each the following instruction execute Μον Bκ,…

A: Given: MOV Bx, 1357hMOV SI, 1234hLES DI, [Bx][SI] To find: To find the content of the register from…

Q: Select an OR instruction that will:

A: A. OR AH, BL B. OR CX, 0088H C. OR SI, DX

Q: . Select an OR instruction that will : a) OR BL with AH and save the result in AH b) OR 88H with CX…

A: Here is the explanation of given OR instruction

Q: Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps.…

A: Dear Student, RCR instruction in 8086 assembly language is used to perform rotations of all the bits…

Q: For the following instructions show which are allowed and not allowed then write the reasons: -SUB…

A: 1. SUB SS, DS -ADD [BX],[300H] Answer: This is not allowed we can not subtract value from The Stack…

Q: Use the following data declarations: .data sbyte 1, 2, 3, FCh word 1000h, 2000h, 3000h, 4000h…

A: Let's go through each code fragment step by step:a.The value at byteVal+2 is 3. So, bh will be…

Q: Memory 12200 12201 12202 12203 12204 Content %3D AA EE FF 22 What result is produced in the…

A: To find result for the following execution instruction. a. LEA SI, [DI + BX + 5] b. LDS SI,[200]

Q: PIC18F87J11 Do the following: a) Copy data 0xA to data memory location 0x400 b) Toggle the value in…

A: SUMMARY: - Hence, we discussed all the points.

Q: AND BX with DX and save the result in BX AND OAEH with DH

A: Here is the solution which is mentioned below : There is a clear explanation given for the…

Q: Q2: Give the addressing mode for each of the following instructions: 1. MOV [CL+1234H], DH…

A: Find the required answer given as below :

Q: If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H,…

A: Answer: It is a base addressing mode. Effective address of the operand obtained by adding direct or…

Q: Select an OR instruction that will: a) OR BL with AH and save the result in AH. b) OR 88H with CX.…

A: Here is the explanation

Question

Determine the memory location of operand 2 of the following instructions:
a) MOV AL, [0100]
b) MOV CL, [BX + 0200] Assume CS = 2300, BX = 1000H, SI = 0100

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Q 4. State whether the following instructions are valid or not. If valid then define properly, if not, then state the reason of their invalidity: MOV [BX + SI + 2], AL XCHG AL, CX ADD 23H, AL
Use the following data declarations: .data byte Val word Val sbyte 1, 2, 3, FCh word 1000h, 2000h, 3000h, 4000h dwordVal dword 34567890h, 90785634h, 0Ah, 33445566h Show the value of the final destination operand after each of the following code fragments has executed: (If any instruction/s is invalid, indicate "INV" as the answer and briefly explain why) a. mov bh,byteVal+2 b. mov edx,1 C. add dx,[wordVal+4] mov ecx,5 xchg ecx,[dwordVal+12] d. mov ah, byte Val+3 sub ah,[ byte Val+0] sub ah,[ byte Val +2] e. mov eax, dword ptr dwordVal+7 f. movsx cx,byteVal+3 answer bh= answer edx= answer ecx= answer ah= answer eax= answer (show your answer in binary) CX=
The instruction that is not possible among the following is a) MOV AX, BX b) MOV AX, [BX]. c) MOV 55H, BL d) MOV AL, 55H
Task: Convert the character in AL to upper case. Solution: Use the AND instruction to clear bit 5. mov al,'a' and al,11011111b ; AL = 01000001b ; AL = 01100001b
Given a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selectedat each multiplexer. You can write "none" for the multiplexers that are not used for this instruction.(a) MUX1:(b) MUX2:(c) MUX3:(d) MUX4:
H\W: assume Ds- 2400, show the content of register as each the following instruction execute Mov Bx, 1357, Mov SI, 1234. ES DI, (Bx) (SI]
1. Describe the operation performed by each of the instructions that follow: d) CMP [0100 H] , AL e) CMP AX, [SI] f) CMP WORD [DI], 1234 H
Select an OR instruction that will:a) OR BL with AH and save the result in AH.b) OR 88H with CX.c) OR DX with SI and save the result in SI.d) OR 1122H with BP.e) OR the data addressed by BX with CX and save the result in memory.f) OR the data stored 40 bytes after the location addressed by BP with AL and save the result in AL.
QI) If BX=1000, DS=0200, SS=0100, CS-0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H, AL. Find the physical address in the memory. Q2) For the above question, if BP is used instead of BX, what is the physical address in the memory?
4. Select an AND instruction that will : a) AND BX with DX and save the result in BX b) AND 0AEH with DH c) AND DI with BP and save the result in DI d) AND the data addressed by BP with CX and save the result in memory e) AND the data stored in four words before the location addressed by SI with DX and save the result in DX
5. Select an OR instruction that will : a) OR BL with AH and save the result in AH b) OR 88H with CX c) OR DX with SI and save the result in SI d) OR 1122H with BP e) OR the data addressed by BX with CX and save the result in memory f) OR the data stored 40 bytes after the location addressed by BP with AL and save the result in AL
For the following instructions show which are allowed and not allowed then write the reasons: -SUB SS, DS -ADD [BX],[300H] -SUB 08, AL -INC [BX+5] -ADC CX, DL