Get the following values for each stage using NIST tables:Stage 5: T5, H5Explain how to get values please. 1) The power plant is operating on iso-butane as a working fluid.Ob-butane mass flow rate is m = 25kg/s. For the input data see the figure.-Feed water: Mass flow rate of the feed water is 200 kg/s.NOTE:This is an ideal Rankine cycle. In this problem we assume 100% efficiency of the turbine andthe pump. The processes are reversible: S1=S2 and S3=S4.Do not change the fluid type!-Use international units to complete calculationsThe P1 pressure corresponds to the critical pointSaturated vaporP1=36.29 barBoilerW.QinTurbineCondenserP2=2.26 bar2T6=?6CoutT5=15C5CoolingwaterPump3saturated liquid

Answered: 1) The power plant is operating on…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
Hello, I need help with the following thermodynamics problem.Thank you! The compined cycle plant shown in figure uses a gas turbine engine operating with 250 kg/s of air entering at 300K and pressure ratio of 12.5.Use an idea air-starndard cycle as a model of this engine and assume the turbine inlet temperature is 1400K. The steam cycle operates in a simple rankine cycle between 10MPa and 70kPa.
In an ideal Rankine Cycle, steam at 5 MPaa and 500 0C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump(kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate SOLVE ALL LETTER PLS : a) Ideal power output of the Turbine (kW), b) Power to drive the pump(kW), c) Rate of Heat Added (kW) d.)thermal efficiency of cycle and engine, e.)steam rate of the cycle and engine in unit (Kg/kw-hr), and f.) Hear Rate in-unit (Kj/kw-hr) PLSS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY ROUND OFF ANSWER TO 4 DECIMAL PLACES . SHOW P-V AND T-S DIAGRAMS PLS PLS REFER TO VALUES OF THE PRESSURE TABLE AND THE SUPERHEATED TABLE IN THE ATTACHMENTS DONT SHOW THE SAME SOLUTION OF OTHERS pls.
3. What are the basic components of Rankine Cycle and draw TS diagrams
Steam enters the turbine 5MPa and 600 and exits adiabatically at 100 kPa. For Actual cycle: turbine efficiency =90%, turbine brake efficiency=84%, generator efficiency=93% Mass flow rate of steam = 15 kg/s Determine the following: For Ideal Rankine Engine Find WT and e SR and HR For Actual Rankine Cycle Find WT’, WB, WK,e’, eB and eK Find SR’, SRB, SRK,HR’, HRB and HRK
Solve by hand please
The Siemans SST-400 GEO steam turbine is employed in the cycle shown above. Operational information is are shown in the table. you can assume the turbine is adiabatic and you can ignore the KE & PE terms. you can assume that the pump operation is isentropic. the surrounding temperature is 25°C based on the table information: a.Calculate the mass flow of steam [96.5kg/s] b.Find the isentropic efficiency of the turbine [0.836] c.What is the rate of entropy generated (kW/K) in the turbine? [28.26kW/K] d.Calculate the thermal efficiency of the power plant [0.199]
A steam power plant operating on iregenerative cylce includes one feedwater heater [back word]. steam enters the turbine at 4500KPA and 500C and extracted from the turbine at 350KPA. what is thermal efficiency of the cycle ? TTD = 5
Problem 3. A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |WNet|- e. Determine the thermal efficiency (n.)
regenerative steam turbine has a throttle pressure of 3.8 MPa at 380 °C and a condenser pressure of 0.1 MPa. Steam are extracted at the following ponts: 2 MPa, 1 MPa, and at 0.2 MPa. For the ideal cycle, find the thermal efficiency.
GA: In a reaction turbine, the angles of receiving tips are 35° and of discharging tips, 20°. The blade speed is 100 m/s. Calculate the tangential force, power developed, diagram efficiency, and axial thrust of the turbine, if its steam consumption is 1 kg/min. Draw the velocity diagram on scale. B: What are the objects of using the condensers in steam plants?
If the Rankine cycle shown in the figure is an "Ideal Rankine cycle", what assumptions do you typically make? Select all that apply: Turbine Boiler Condenser - Qout (KL: 45 sec) (Chien-Ming: 1 min) RR: up to 1min NT = 100% O Wr > Wp O State 4 is a saturated liquid O X3 = 1

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS