Module 3 Unit 3 Assignment A

Part II. Longer problem focused on problem solving multiple steps. This problem will be graded based on process, clarity of work, and correct answer and units. a. A spring is stretched, with a force, F = 442 lbf, along the outside of a pipe as shown with a = 53° and ẞ 69° and the coordinates of the force are (15,37,-71 ). How far does the spring stretch if the spring constant is k=67 lb/in? Hint: The force that stretches the spring is the projected force along the pipe F (x, y, z)

Please provide a complete solution. Our subject is FLUID MECHANIC

Please show work in a handwritten format. Don't use chatgpt. Mechanics of materials/design.

Newton's Law of cooling states that the rate at which heat is lost by a heated body is proportional to the difference in temperature between the body and the surrounding medium. Match the following statements/phrases with the corresponding item in the drop down box. Choices in the box 1. In accordance with the stated law obove, we have the equation? 2. If a thermometer is taken outdoors where the temperoture is 5 deg C, from a room in which the temperature is 20 deg C and the reading drops 10 deg C in one minute, the working equation is? 3. In the obove problem, separoting the variables and integrating will result to? 4. In the obove problem, how long, in minutes, after its removal from the room will the reading be 6 deg C? 5. In the obove problem, ofter 30 seconds, whot will be the thermometer reading? 5.2 dT(body temp)/dt = k(Temp of medium - 5) dr(body temp)/dt = k(Temp of body - Temp of medium) Temp of body = Cenkt +5 2.5 13.7 dr(body temp)/dt = k(Temp of medium - Temp of body)…

Handwritten solution required. Strictly don't use chatgpt. If you use chatgpt ,I will report the answer for sure. Mechanical engineering dynamics.

Please solve d) and e) only. Thank you.

Considering the results in Table 1, and the documentation in the image too, please calculate the dynamic viscosity for the fluids listed in Table 3.

Pressurized eyes Our eyes need a certain amount of internal pressure in order to work properly, with the normal range being between 10 and 20 mm of mercury. The pressure is determined by a balance between the fluid entering and leaving the eye. If the pressure is above the normal level, damage may occur to the optic nerve where it leaves the eye, leading to a loss of the visual field termed glaucoma. Measurement of the pressure within the eye can be done by several different noninvasive types of instruments, all of which measure the slight deformation of the eyeball when a force is put on it. Some methods use a physical probe that makes contact with the front of the eye, applies a known force, and measures the deformation. One non-contact method uses a calibrated “puff” of air that is blown against the eye. The stagnation pressure resulting from the air blowing against the eyeball causes a slight deformation, the magnitude of which is correlated with the pressure within the eyeball.…

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…

Fluid mechanics A measure of the stiffness of a linear actuator system is the amount of force required to cause a certain linear de- flection. For an actuator that has an inside diameter of 0.50 in and a length of 42.0 in and that is filled with ma- chine oil, compute the stiffness in lb/in.

please help me with this

These are the questions and the corresponding figure for the questions, make sure for each question the answers are neat and readable.

Please solve what is ask with complete handwritten solution, Thank you so much!