AM-Lab Report Template withACAHR-Fall2023

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

Help!!! Please answer all Correctly!!! Please

Please answer the 4th question

I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question, then just leave it for someone else to answer. I've never had an issue until recently one single tutor just refuses to even read the instructions of the question and just denies it for a false reasons or drags on 1 part into multiple parts for no reason.

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Please give a complete solution in Handwritten format. Strictly don't use chatgpt,I need correct answer. Engineering dynamics

University of Babylon Collage of Engineering/ Al-Musayab Department of Automobiles Final Examination/ Stage: 3rd Notes: Answer 4 questions only 2023-2202 Subject: Theory of vehicles Date: 2023\06\10-Saturday Time: Three Hours Course 2nd Attempt 1st Q1: A Hooke's coupling connects two shafts whose axes are inclined at 30°. The of the driven shaft? Find the maximum value of retardation or acceleration and driving shaft rotates uniformly at 600 rpm. What are the extreme angular velocities state the angle where both will occur. (12.5 Marks) Q2: Four masses, A, B, C, and D), revolve at equal radii and are equally spaced along a shaft. The mass B is 7 kg, and the radius of C and D make angles of 90° and 240°, respectively, with the radius of B. Find the magnitude of the masses A, C, and D and the angular position of A so that the system may be completely balanced. (12.5 Marks) Q3: A cam has straight worked faces that are tangential to a base circle of diameter 90 mm. The follower is a roller…

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

University of Babylon Collage of Engineering/ Al-Musayab Department of Automobiles Mid Examination/ Stage: 3rd Subject: Theory of Vehicles Date: 14 \ 4 \2025 Time: 1.5 Hours 2025-2024 Q1: The arms of a Porter governor are 250 mm long. The upper arms are pivoted on the axis of revolution, but the lower arms are attached to a sleeve at a distance of 50 mm from the axis of rotation. The weight on the sleeve is 600 N and the weight of each ball is 80 N. Determine the equilibrium speed when the radius of rotation of the balls is 150 mm. If the friction is equivalent to a load of 25 N at the sleeve, determine the range of speed for this position. Q2: In a loaded Proell governor shown in Figure below each ball weighs 3 kg and the central sleeve weighs 25 kg. The arms are of 200 mm length and pivoted about axis displaced from the central axis of rotation by 38.5 mm, y=238 mm, x=303.5 mm, CE 85 mm, MD 142.5 mm. Determine the equilibrium speed. Fe mg E M 2 Q3: In a spring loaded Hartnell type…

Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question is Attached in image. Thank you.

Please solve, engineering econ

Help!!! Please answer part b correctly like part A. Please!!!!

How may acoustic designers alter the design of a room, which was previously used for music performances, into a room now to be used for spoken word performances? Use annotated diagrams for your response

FINALS ASSIGNMENT IN ME 3215 COMBUSTION ENGINEERING PROBLEM 1: A Diesel engine overcome a friction of 200 HP and delivers 1000 BHP. Air consumption is 90 kg per minute. The Air/fuel ratio is 15 to 1. Find the following: 1. Indicated horsepower 2. The Mechanical efficiency 3. The Brake Specific Fuel Consumption PROBLEM 2: The brake thermal efficiency of a diesel engine is 30 percent. If the air to fuel ratio by weight is 20 and the calorific value of the fuel used is 41800 kJ/kg, what brake mean effective pressure may be expected at S.P. conditions (Standard Temperature and pressure means 15.6°C and 101.325 kPa, respectively)?

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk

Please give me the answers for this i been looking at this for a hour and my head hurts

Mechanical Advantage Review Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your engineering design journal. Remember to show all work. 1. A lever has an effort arm that is 8 meters long and the resistance (load) arm that is 5 meters long, how much effort is needed to lift a 200 Newton weight?

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Case Study – The New Engineer   Jeff was just hired by GSI, Inc. to be their Environmental and Safety Coordinator.  This is Jeff's first position after completing his engineering degree.  He had taken a course in safety engineering as part of his studies and felt confident that he could handle the job.   Management at GSI, Inc. has assured him that they are committed to maintaining a safe workplace.  They have never had an individual dedicated to this task full-time.  They will implement his recommendations if he can justify them.   As Jeff begins to get familiar with the operations, he spends considerable time on the production floor.  He notices workers clean their tools before break with a liquid from an unmarked 55-gallon drum.  They also use this liquid to clean residue from their skin.  They use paper towels to dry their tools and hands, throw these towels in the trash, and head to the break room for a snack and/or smoke.   In talking with the workers, Jeff learns of some of…

Access Pearson Mastering Engineering Back to my courses Course Home Course Home Scores ■Review Next >