LSC-Lab-Report-Template (1) (1)

Truncation errors are increased as the round-off errors are decreased.Group of answer choices True False Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 29oC, 29.2oC, 29.3oC, 28.9oC, and 29.1oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is not accurate and not precise The thermometer is faulty. The thermometer is accurate and precise The thermometer is not accurate but precise. Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 36oC, 35.6oC, 36oC, 37oC, and 36.2oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is accurate and precise. The thermometer is accurate but not precise. The…

Topics: Statics of Rigid Bodies, Equilibrium of Rigid Bodies, Equilibrium in Two Dimensions, etc.   I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION.   If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.”    THANK YOU FOR YOUR HELP.   PS: If you have answered this already, don’t answer it again; give chance to other experts to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times. If you answer it again, i'll dislike all your entries/answers.

Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate the units of each measurement. Calculate the average length of each side of the block. Dimension Caliper (Units) 0.995 1.455 0.985 Ruler(in) A: 0.9 B: 1.5 C: 0.9 A B C Dimension A B Instrument Use the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record the voltage on the table below: LVDT Offset: 0.556 (Do not include the offset value in your average dimensions) C Ave Dimension (Units) (Dial Gauge) 0.997 1.659 0.949 0.964 in 1.538 in 0.945 in oltage Average Dimension 1.244 volt 1.994 1.28 0.964 in 1.538 in 0.945 in

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

Show work Part 1 website: https://ophysics.com/r5.html PArt 2 website: https://ophysics.com/r3.html

Question 4

Please give a complete solution in Handwritten format. Strictly don't use chatgpt,I need correct answer. Engineering dynamics

Help!!! Please answer all Correctly!!! Please

Help and the answers choice is A) robin is correct B)Pilar is correct C)aaron is correct D) Anthony is correct

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

Study Area Document Sharing User Settings Access Pearson mylabmastering.pearson.com P Pearson MyLab and Mastering The crash cushion for a highway barrier consists of a nest of barrels filled with an impact-absorbing material. The barrier stopping force is measured versus the vehicle penetration into the barrier. (Figure 1) Part A P Course Home b My Questions | bartleby Review Determine the distance a car having a weight of 4000 lb will penetrate the barrier if it is originally traveling at 55 ft/s when it strikes the first barrel. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 36 μΑ S = Value Units Submit Request Answer Provide Feedback ? Next >

dear tutor please provide neat and clean and detailed answer. dont copy from google adress both questions well

I want to briefly summarize what he is talking about and what you conclude. pls very urgent

7. Why are land and groove markings on a bullet considered Class Evidence, while the striation markings on a bullet are consider Individual Evidence? 8. You recover two bullets from the wall of a crime scene. These recovered bullets are visible below: Bullet #1 Enlarged View Enlarged View Bullet #2 Actual Size Actual Size Bottom View Bottom View Bottom View Bottom View Complete the Evidence Table below. You can easily convert millimeters to inches (if needed) using the following formula: # of millimeters # of inches 25.4 mm per inch Firearm likely produced by what manufacturer? Approximate Bullet Evidence Table Direction of # of Lands Caliber Twist (English) Bullet #1 Bullet #2 Do you believe that Bullet #1 and Bullet #2 were fired from the same gun? 86