BI196 Tutorial 1 activity sheet W22 (2)

Help with this would be great, thanks!

Please answer the 4th question

Help with this would be great, thanks!

Mech. Engg. Dept. 4th year 2022-2023 Solar Energy Spring course MEC364 Dr. Mahmoud U. Jasim Review/Recap Sheet Q1- Answer with true or false and rewrite the false statements completely in correct form, otherwise no mark will be put on the false statements. 1 2 To represent a location on earth surface you need to define its altitude and longitude angles. 3 Solar zenith and solar incidence angles have the same value for horizontal surface. At sunset time the value of solar altitude angle is maximum. 4 The angle which represents the inclination of a given surface is the zenith angle 5 6 7 8 When the absolute value of sun-wall azimuth angle exceeds 90' this means that the sun rays are reaching the receiving plane. The solar irradiance and the solar irradiation have the same physical meaning. In the case of clear sky weather, the beam solar irradiation on a horizontal surface is less than the diffused irradiation. The total solar radiation received by a tilted surface is the same as that…

operations research -  pert cpm

Solve all parts

I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question, then just leave it for someone else to answer. I've never had an issue until recently one single tutor just refuses to even read the instructions of the question and just denies it for a false reasons or drags on 1 part into multiple parts for no reason.

Do not give answer in image and hand writing

J 6

Help!!! Answer it correctly!!! Make sure you solve work on hand!!! Answer correctly Please!!!!!!!

This is an engineering problem and not a writing assignment. Please Do Not Reject. I had other engineering tutors on bartleby help me with problems similar to this one. This problem must be presented in a logical order showing the necessary steps used to arrive at an answer. Each homework problem should have the following items unless otherwise stated in the problem: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. Most sources will be from a table in the textbook (i.e. Table A-4). e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an…

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk

I need problems 6 and 7 solved.  I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1

I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered. NOTE: Read the instructions, no where does it say any drawing is required. It is really frustrating when I wait all this time for an answer to a question and some tutor does even read the instructions and just declines it...its ridicilous.

Do not give answer in image and hand writing

all one question help asap please!

Full Answer PLEASE!.  Answer Q 3 and 4 PLease Don't copy from the internet. PLEASE WRITE YOUR OWN WORDS THANK YOU

please help solve A-F. thank you You are an engineer working on a project and your prototype has failed prematurely. You question whether or not a key component of the prototype was manufactured with the correct material. There are two way to check for the material properties. The first way is to have a material certification done to confirm the exact material composition. This will take some time. The second method to confirm the material properties is to make an ASTM test sample and test for the material properties. This tensile test was completed on a test sample with an initial diameter of .501” and an initial length of 2”. The Load-Deflection data for this tensile test is below. Use this data to answer the first set of questions on the Final Exam in eLearning. A. Determine the Ultimate Tensile Strength B. Determine the 0.2% Offset Yield Strength C. Determine the value of the Proportional Limit D. Determine the Modulus of Elasticity E. Determine the Strain at Yield F. Calculate %…

This is the complete question and not a writing assignment. Make sure for this problem you list the following: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an appropriate number of significant figures.

LESSON: AUTODESK AUTOCAD Choose from the choices:

LESSON: AUTODESK AUTOCAD Choose from the choices:

I need answers to problems 7, 8, and 9.  NOTE: Please stop wasting my time and yours by rejecting my question because it DOES NOT REQUIRE YOU TO DRAW anything at all. They are simple questions pertaining to the print provided. READ THE INSTRUCTIONS of the assignment before you just reject it for a FALSE reason or leave it for someone to answer that actually wants to do their job. Thanks.

1) A low-friction cart is placed between two identical springs attached to rigid walls. If you push the cart against one of the springs and release it, it will continue to move back and forth between the springs. www Draw a force-time graph showing the sum of the horizontal forces exerted on the cart as it moves back and force between the springs. Scientific Abilities Is able to construct a force diagram Missing No representation is constructed. Inadequate FD is constructed but contains major errors such as incorrect mislabeled or not labeled force vectors, length of vectors, wrong direction, extra incorrect vectors are added, or vectors are missing. Needs Improvement FD contains no errors in vectors but lacks a key feature such as labels of forces with two subscripts or vectors are not drawn from single point, or axes are missing. Adequate The diagram contains no errors and each force is labeled so that it is clearly understood what each force represents. Explain whether or not this…