Head & Neck Exam

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

You go on a road trip to escape the cold winter days of Kirkland Lake, Ontario to the warm beaches of Moonbeam, Ontario. Since it is a long drive and you are leaving early in the morning, you make sure to check the tire pressure and make sure it is at the recommended level. At lunchtime, you stop for gas and decide to check your car's tire pressure again. You also notice that the tires seem to be a little bit larger than when you left. The driver's manual suggests a pressure between 205 and 220 kPa. Knowing that the tires heat up while driving; do you expect your reading to be high, low or the same as the recommended tire pressure? Why? Since you plan on staying in Moonbeam a while to see the sights, you think it would be best to adjust your tire pressure. What adjustments should be made to your tires? Should you make these adjustments as soon as you arrive, or the following day?

Show work Part 1 website: https://ophysics.com/r5.html PArt 2 website: https://ophysics.com/r3.html

I want to briefly summarize what he is talking about and what you conclude. pls very urgent

I want to briefly summarize what he is talking about.

As an engineer responsible for monitoring works in the area of ​​mechanical systems, you must evaluate the following situation: a large client in the retail area has a refrigeration system where it stores some chilled or frozen products to be sold on the sales floor.Recently, the customer's maintenance department has been questioning the system's performance and requested an evaluation of the system's behavior. You went to the location and requested some information from the maintenance manager about the system, who provided the following data: - The system operates with R-134a refrigerant;- The refrigerated environment is maintained at 0°C and the external environment at 26°C;- The refrigerant flow rate in the system is 0.08 kg/s; In addition to the data provided, you carried out some tests and measured the temperature of the refrigerant fluid at some specific points in the system, such as the compressor inlet and condenser outlet, finding values ​​of 0°C and 26°C respectively.…

As an engineer responsible for monitoring works in the area of ​​mechanical systems, you must evaluate the following situation: a large client in the retail area has a refrigeration system where it stores some chilled or frozen products to be sold on the sales floor.Recently, the customer's maintenance department has been questioning the system's performance and requested an evaluation of the system's behavior. You went to the location and requested some information from the maintenance manager about the system, who provided the following data: - The system operates with R-134a refrigerant;- The refrigerated environment is maintained at 0°C and the external environment at 26°C;- The refrigerant flow rate in the system is 0.08 kg/s; In addition to the data provided, you carried out some tests and measured the temperature of the refrigerant fluid at some specific points in the system, such as the compressor inlet and condenser outlet, finding values ​​of 0°C and 26°C respectively.…

Need help

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Question 45 is based on the following picture. Reprinted with permission from Popular Science magazine, ©2000, Times Mirror Magazines, Inc. 45. Stuart Wilkinson, the engineer of "Chew- Chew" said, "we stole the idea of eating food from the biological world, but we are marrying that idea to useful robotic capabilities." Which of the following would not be an application of Stuart Wilkinson's theory? A. A leaf mulcher that feeds on foliage B. a trash compactor that feeds on garbage dos C. a lawn mower that feeds on grass bos 9D. a garden cultivator that feeds on soil clippings E. a recycling truck that feeds on petroleum conjo

Im not sure how ro go about this, can you help me figure out these answers or how to get these answers?