HI255_Unit_5_assignment_worksheet_2303B

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

Please answer the 4th question

I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

Please give me the answers for this i been looking at this for a hour and my head hurts

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

I need help solving problems 10, 11, and 12 pertaining to the print provided.

A nearsighted eye is corrected by placing a diverging lens in front of the eye. The lens will create a virtual image of a distant object at the far point (the farthest an object can be from the eye and still be in focus) of the myopic viewer where it will be clearly seen. In the traditional treatment of myopia, an object at infinity is focused to the far point of the eye. If an individual has a far point of 39.5 cm, prescribe the correct power of the lens that is needed. Assume that the distance from the eye to the lens is negligible.

A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.  You must follow the following steps to help the team:  STEP 1  Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:  The input and output heat and net output work The expansion and compression strokes The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work. STEP 2  Explain the mechanical…

I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.

11)

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…

I need help with problems 1, 2, and 3 pertaining to the print provided below.

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk

The Weather Monitor. Your South American expedition splits into two groups: one that stays at home base, and yours that goes off to set up a sensor that will monitor precipitation, temperature, and sunlight through the upcoming winter. The sensor must link up to a central communications system at base camp that simultaneously uploads the data from numerous sensors to a satellite. In order to set up and calibrate the sensor, you will have to communicate with base camp to give them specific location information. Unfortunately, the group's communication and navigation equipment has dwindled to walkie-talkies and a compass due to a river-raft mishap, which means your group must not exceed the range of the walkie-talkies (3.0 miles). However, you do have a laser rangefinder to help you measure distances as you navigate with the compass. After a few hours of hiking, you find the perfect plateau on which to mount the sensor. You have carefully mapped your path from base camp around lakes and…

I need help answering questions 4, 5, and 6 pertaining to the print provided below.

Identify the lines

The question and data are in pictures. Please answer properly with each steps and explanation. Best of luck. Thank you so much in advance.

4 of 11 Plane-Stress Transformation Learning Goal: The state of in-plane stress at a point on an element of material is shown. Let |ox| = 320 MPa, |oy| = 120 MPa, and |Txy| = 75.0 MPa. Use this information to represent the state of stress of the same point that is rotated through an angle of 0 = 25.0°. b Txy σx Part A - Normal and shear stress on element sectioned at plane a-a Using the element sectioned at plane a-a and the rotated coordinate system shown, determine the normal and shear stresses, σ and Ta'y', respectively, acting on plane a-a. 90-0 -90-8 X Express your answers in MPa to three significant figures separated by a comma. 0