IMG_1579

15)This multiple choice question from MEASUREMENTS INSTRUMENTATIONS course.

Please help. You are going to draw arrows that indicates the flow of the given 5 actions (a,b,c,d,e). You can draw arrows for all of them in the picture above, or make separate drawing for each letter. Please help me this is about CARRIER ACTION/FLOW OF CARRIERS in a semiconductor. It is also about Ferni Level.

FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…

This is a practice question from my Introduction to Electronics course. Could you please walk me through the process of solving this so that I can figure out more complex circuits? Thank you for your assistance.

Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below (assume Si diodes) V_DC V DC 0,75 (1+ 0.25 V_SIN V SIN RL -1 V SOR V_SQR 0.75 -0.75 V TRI 1 V_TRI -1

11

Can you please help me with this homework question? Will thumbs up

The circle is below(for D1-1N4148 is 1N4148 Diode).  and also there have a table(. Note that the first 3 rows of measurement are obtained when the diode is reverse-biased) Vout_dc (V) VD (V) ID (μA) 0.51 -0.51 0.0 0.23 -0.20 0.0 0.10 -0.08 0.0 0.00 0.00 0.0 0.05 0.04 0.0 0.11 0.09 0.0 0.17 0.15 0.1 0.19 0.20 0.1 0.27  0.25 0.4 0.32 0.30 1.6 0.36 0.34 3.1 0.42 0.40 8.2 0.46 0.42 14.3 0.52 0.47 28.0 Questions: 1)  plot the diode’s I-V characteristics on a linear scale (ID on the y-axis and VD on the x-axis)  2)  [RP4] 3)  [RP5]

Convert following number in the given radix system.(a) (1010.011)2 to (…………)10(b) (0.513)10 to (……….)8

In Figure-1 (a and b), calculate the load current, load voltage, load power, diode power, and total power using 3d approximation if Rp 802 and diode current is 10 mA. Note please solve within 30 minutes.avoid plagiarism

Use your reasoning logic to determine which diodes are on and which might be off in the following circuit, assuming the diode drops are 0.7 V.   A. VA B. VB C(ID1) D(ID2) E(ID3)

v Question Completion Status: forward-biased QUESTION 2 For this clipping circuit, what will be the minimum output voltage when diode is conducting? 10002 120VAC ideal 2,5 V 10:1 +19.47 Volts 25 Volt KA6.97 olts ON E97 Volts QUESTION 3 Click Save oand Submit to save and submit. Click Save AllAnswers to save all ansuers. Sa

1. Answer the subparts A&B with the step, based on the Image. This question Q&A please no reject and solve thank u A) Based on the measurement data above, indicate that there is an error in the measurement      data. Give an explanation of the answers given. B) Determine in which element there is an error in the measurement data. What should be       the correct measurement result. Give an explanation of the answers given.

Can you help me set up my breadboard so I can ... Measure the values of base current, _________, collector current, _________ ?