Copy of 5CL Pre-Lab 5 Response

The question is attached to jpeg picture of the circuit:

Please review the images.

uo A:EV * ll. pluli ► b89f3244-f736-4021-901... PI EXPlain The effect of increasing The filter Capacitance on The outfut Voltage in The haif - wave rectifier and filber Circuit ? CS Scanned with CamScanner

De fine time constant (I) for (R-L) cct.

please label the questions

0please see both images to solve

Consider the figure shown below. The MPT32 is a diac with a breakover voltage of 32 V. a) b) c) If the triac has a trigger voltage of 0.7 V, What must be the capacitor voltage that triggers the triac? If the triac in the figure shown below has 1 V across it when it is conducting, what is the maximum current through the 500 resistor? What must be the value of the source to start turning off the triac? +50V 7 -50V 50ΚΩ 1kΩ W 1 uF 500 Ω W MPT32 Triac IT.= 15 mA IH= 10 mA

FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…

Dont use chat gpt need pen paper solution otherwise dislike

Write a PIC16F877A program that flash ON the 8-LED's connected to port-B by using two switches connected to port-D (Do & D₁) as shown in figure below, according to the following scenarios: (Hint: Use 500ms delay for each case with 4MHz frequency) 1. When Do=1 then B₁,B3,B7 are ON. 2. When Do 0 then Bo,B2, B4, B5, B6 are ON. 3. When D=1 then B4, B5, B6, B7 are ON. 4. When D₁=0 then B0,B1,B2,B3 are ON. U1 OSC1/CLION 33 OSC2/CLKOUT T 34 5 U2 20 10 35 3 18 10 - 30 -ou-un RB2 2 RA1/AN1 PA3/AN3VREF+ RA4/TOCKIC1OUT RACIANO 0RB3PGM 37 33 4 17 5 10 RB4 39 RA2/ANZ/VREF-CVREF RB5 15 39 7 14 RB6PGC 40 13 RB7/PGO RAS/AN4/SS/C2OUT + 15 RCOT1OSOTICK 10 RECANARD RE1/AN/R REZ/ANTICS ✓ MCLR/Vpp/THV RC2/CCP1 RC3/SCK/SCL RCA/SOISDA RC5/S00 RCB/TX/CK 10 RC1/T10SUCCP2 17 LED-BARGRAPH-RED RC7/RX/DT ROOPSPO RD1/PSP1 R02/PSP2 RD3/PSP3 ROUPSP4 RD5PSP5 ROOPSPO RO7/PSP7 PIC16F877A +5V R2 100R R1 100R