The IUPAC name for the given compound is to be determined. Concept introduction: In case of molecules containing a C=C or C ≡ C bond, the longest continuous carbon chain or largest ring that contains the double or triple bond is considered as the root. It is possible that the longest carbon chain has more carbons than specified by the root. But the double or triple bond must be a part of the root. The root is named from the name of the analogous alkane or cycloalkane by replacing the suffix ane by ene if a double bond is present. The suffix ane is replaced by yne if a triple bond is present. If the root is a chain, the numbering begins from that end of the chain, which encounters the C=C or C ≡ C at the earliest. If there is a tie, then the chain is numbered such that the substituents get the lowest locator numbers. If the root is a ring, then the double or triple bonded carbon atoms are always numbered as C1 and C2. This must be done such that the locator numbers for the substituents are minimized. The lower of the two locator numbers for the C=C or C ≡ C is written before the ene or yne suffix. Prefixes and locator numbers are used for the substituents attached.

Question

Want to see the full answer?

Answer 1

Question

Chapter B, Problem B.3P

Interpretation Introduction

Interpretation:

The IUPAC name for the given compound is to be determined.

Concept introduction:

In case of molecules containing a C=C or C≡C bond, the longest continuous carbon chain or largest ring that contains the double or triple bond is considered as the root. It is possible that the longest carbon chain has more carbons than specified by the root. But the double or triple bond must be a part of the root. The root is named from the name of the analogous alkane or cycloalkane by replacing the suffix ane by ene if a double bond is present. The suffix ane is replaced by yne if a triple bond is present.

If the root is a chain, the numbering begins from that end of the chain, which encounters the C=C or C≡C at the earliest. If there is a tie, then the chain is numbered such that the substituents get the lowest locator numbers.

If the root is a ring, then the double or triple bonded carbon atoms are always numbered as C1 and C2. This must be done such that the locator numbers for the substituents are minimized. The lower of the two locator numbers for the C=C or C≡C is written before the ene or yne suffix. Prefixes and locator numbers are used for the substituents attached.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

On the next page is an LC separation of the parabens found in baby wash. Parabens are suspected in a link to breast cancer therefore an accurate way to quantitate them is desired. a. In the chromatogram, estimate k' for ethyl paraben. Clearly indicate what values you used for all the terms in your calculation. b. Is this a "good" value for a capacity factor? Explain. c. What is the resolution between n-Propyl paraben and n-Butyl paraben? Again, indicate clearly what values you used in your calculation. MAU | Methyl paraben 40 20 0 -2 Ethyl paraben n-Propyl paraben n-Butyl paraben App ID 22925 6 8 min

d. In Figure 4, each stationary phase shows some negative correlation between plate count and retention factor. In other words, as k' increases, N decreases. Explain this relationship between k' and N. Plate Count (N) 4000 3500 2500 2000 1500 1000 Figure 4. Column efficiency (N) vs retention factor (k') for 22 nonionizable solutes on FMS (red), PGC (black), and COZ (green). 3000 Eluent compositions (acetonitrile/water, A/W) were adjusted to obtain k' less than 15, which was achieved for most solutes as follows: FMS (30/70 A/W), PGC (60/40), COZ (80/20). Slightly different compositions were used for the most highly retained solutes. All columns were 50 mm × 4.6 mm id and packed with 5 um particles, except for COZ, which was packed with 3 um particles. All other chromatographic conditions were constant: column length 5 cm, column j.§. 4.6 mm, flow rate 2 mL/min, column temperature 40 °C, and injection volume 0.5 μL Log(k'x/K'ethylbenzene) FMS 1.5 1.0 0.5 0.0 ཐྭ ཋ ཤྩ བྷྲ ; 500 0 5 10…

f. Predict how the van Deemter curve in Figure 7 would change if the temperature were raised from 40 °C to 55 °C. Figure 7. van Desmter curves in reduced coordinates for four nitroalkane homologues (nitropropane, black; nitrobutane, red; nitropentane, blue; and nitrohexane, green) separated on the FMS phase. Chromatographic conditions: column dimensions 50 mm × 4.6 mm id, eluent 30/70 ACN/water, flow rates 0.2-5.0 mL/min, injection volume 0.5 and column temperature 40 °C. No corrections to the plate heights have been made to account for extracolumn dispersion. Reduced Plate Height (h) ° 20 40 60 Reduced Velocity (v) 8. (2) A water sample is analyzed for traces of benzene using headspace analysis. The sample and standard are spiked with a fixed amount of toluene as an internal standard. The following data are obtained: Ppb benzene Peak area benzene Peak area toluene 10.0 252 376 Sample 533 368 What is the concentration of benzene in the sample?