Explanation Write the expression for the reduced pressure at state 5. p ′ r 5 = ( p 5 p 4 ) p ′ r 4 (I) Here, the pressure at state 4 is p 4 , the pressure at state 5 is p 5 , the pressure at state 5 is p 5 , the reduced pressure at state 5 is p ′ r 5 and the reduced pressure at state 4 is p ′ r 4 . Write the expression for the velocity at the nozzle exit. V 5 = 2 ( h ′ 4 − h ′ 5 ) (II) Here, the velocity at the nozzle exit is V 5 , the specific enthalpy at state 4 is h ′ 4 and the specific enthalpy at state 5 is h ′ 5 . Conclusion: Refer to table A-22 “ideal gas properties of air” to obtain the specific enthalpy and reduced pressure at temperature T ′ 4 = 1300 K as 1395.97 kJ / kg and 330.9 . Substitute 163.4 kPa for p 4 , 330.9 for p ′ r 4 and 26 kPa for p 3 in Equation (I). p ′ r 5 = ( 26 kPa 163

Fundamentals of Engineering Thermodynamics

8th Edition

ISBN: 9781118832301

Author: SHAPIRO

Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT

See similar textbooks

Videos

Question

Chapter 9.14, Problem 88P

To determine

The velocity at the nozzle exit.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.14, Problem 87P

Chapter 9.14, Problem 89P

Students have asked these similar questions

Consider 0.65 kg of N2 at 300 K, 1 bar contained in a rigid tank connected by a valve to another rigid tank holding 0.3 kg of CO2 at 300 K, 1 bar. The valve is opened and gases are allowed to mix, achieving an equilibrium state at 290 K. Determine: (a) the volume of each tank, in m³. (b) the final pressure, in bar. (c) the magnitude of the heat transfer to or from the gases during the process, in kJ. (d) the entropy change of each gas and of the overall system, in kJ/K.

(Read Image) (Answer: ω = 1.10 rad/sec CW)

What is the configuration of the control loop if steam must be shut down in case of a problem? (I found this question on the internet and was wondering what the answer is) A.Valve is fail open, PIC is direct-acting, TIC is reverse acting, and controller algorithm is feed-forwarding.B. Valve is fail open, PIC is reverse-acting, TIC is direct acting, and controller algorithm is cascade.C. Valve is fail closed, PIC is direct-acting, TIC is reverse acting, and controller algorithm is feed-forward.D. Valve is fail closed, PIC is reverse-acting, TIC is reverse acting, and controller algorithm is cascade.

Chapter 9 Solutions

Fundamentals of Engineering Thermodynamics

Ch. 9.14 - Prob. 1E Ch. 9.14 - Prob. 2E Ch. 9.14 - Prob. 3E Ch. 9.14 - Prob. 4E Ch. 9.14 - Prob. 5E Ch. 9.14 - 6. What is the purpose of a rear diffuser on a...Ch. 9.14 - 7. What is the meaning of the octane rating that...Ch. 9.14 - Prob. 8E Ch. 9.14 - Prob. 9E Ch. 9.14 - 10. What is the purpose of the gas turbine–powered...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.