Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the cycle is 6, and the minimum and maximum temperatures are 300 and 1300 K, respectively. Now the pressure ratio is doubled without changing the minimum and maximum temperatures in the cycle. Determine the change in (a) the net work output per unit mass and (b) the thermal efficiency of the cycle as a result of this modification. Assume variable specific heats for air.
a)
The change in net work output per unit mass.
Answer to Problem 164RP
The change in net work output per unit mass is
Explanation of Solution
Draw the
Write the expression for the pressure ratio in terms of relative pressure to calculate the relative pressure at state 2
Here, compressor inlet pressure is
Write the expression for the pressure ratio in terms of relative pressure to calculate the relative pressure at state 4
Here, compressor inlet pressure is
Write the expression for the heat added
Here, specific enthalpy of air from the exit of compressor is
Write the expression for the heat rejected
Here, specific enthalpy of air at the exit of the turbine is
Write the expression for net work done
Write the expression for net work done
Write the expression for the thermal efficiency
Write the expression for the thermal efficiency
Write the expression for change in the net work
Here, net work done for the initial cycle is
Conclusion:
For relative pressure
From the Table A-17, “Ideal-gas properties of air” obtain the following properties at temperature
From the Table A-17, “Ideal-gas properties of air” obtain the following properties at temperature
Substitute
Substitute
From the Table A-17, “Ideal-gas properties of air”.
Obtain the value of enthalpy at state 2
Write the formula of interpolation method of two variables.
Here, the variables denoted by x and y are relative pressure and enthalpy.
Show relative pressure and enthalpy values from the Table A-17.
Relative pressure | Enthalpy |
7.824 | 492.74 |
8.316 | ? |
8.411 | 503.02 |
Substitute
The value of enthalpy at state 2
Similarly by using interpolation method obtain the value of enthalpy at state 4
Substitute
Substitute
Substitute
Substitute
For relative pressure
Substitute
From the Table A-17, “Ideal-gas properties of air” obtain the values of enthalpy
Substitute
From the Table A-17, “Ideal-gas properties of air” obtain the values of enthalpy
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the change in net work output per unit mass is
b)
The change in thermal efficiency of the cycle.
Answer to Problem 164RP
The change in thermal efficiency of the cycle is
Explanation of Solution
Write the expression to calculate the change in thermal efficiency
Conclusion:
Substitute
Thus, the change in thermal efficiency of the cycle is
Want to see more full solutions like this?
Chapter 9 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
- Q2/ The bumper springs of a railway carriage are to be made of rectangular section wire. The ratio of the longer side of the wire to its shorter side is 1.5, and the ratio of mean diameter of spring to the longer side of wire is nearly equal to 6. Three such springs are required to bring to rest a carriage weighing 25 kN moving with a velocity of 75 m/min with a maximum deflection of 200 mm. Determine the sides of the rectangular section of the wire and the mean diameter of coils when the shorter side is parallel to the axis of the spring. The allowable shear stress is not to exceed 300 MPa and G = 84 kN/mm². Q6/ A belicalarrow_forward11. A load of 2 kN is dropped axially on a close coiled helical spring, from a height of 250 mm. The spring has 20 effective turns, and it is made of 25 mm diameter wire. The spring index is 8. Find the maximum shear stress induced in the spring and the amount of compression produced. The modulus of rigidity for the material of the spring wire is 84 kN/mm². [Ans. 287 MPa; 290 mm]arrow_forwardWhat is the reason for this composition?arrow_forward
- Homework: ANOVA Table for followed design B AB Dr -1 -1 1 (15.18,12) 1 -1 -1 (45.48.51) -1 1 -1 (25,28,19) 1 1 (75.75,81)arrow_forwardS B Pin 6 mm Garrow_forwardMid-Term Exam 2024/2025 Post graduate/Applied Mechanics- Metallurgy Q1/ State the type of fault in the following case, and state the structure in which it will appear. АВСАВСВАСВАСАВСАВСarrow_forward
- الثانية Babakt Momentum equation for Boundary Layer S SS -Txfriction dray Momentum equation for Boundary Layer What laws are important for resolving issues 2 How to draw. 3 What's Point about this.arrow_forwardR αι g The system given on the left, consists of three pulleys and the depicted vertical ropes. Given: ri J₁, m1 R = 2r; απ r2, J2, m₂ m1; m2; M3 J1 J2 J3 J3, m3 a) Determine the radii 2 and 3.arrow_forwardB: Solid rotating shaft used in the boat with high speed shown in Figure. The amount of power transmitted at the greatest torque is 224 kW with 130 r.p.m. Used DE-Goodman theory to determine the shaft diameter. Take the shaft material is annealed AISI 1030, the endurance limit of 18.86 kpsi and a factor of safety 1. Which criterion is more conservative? Note: all dimensions in mm. 1 AA Motor 300 Thrust Bearing Sprocket 100 9750 เอarrow_forward
- Q2: The plate material of a pressure vessel is AISI 1050 QT 205 °C. The plate is rolled to a diameter of 1.2 m. The two sides of the plate are connected via a riveted joint as shown below. If the rivet material is G10500 with HB=197 and all rivet sizes M31. Find the required rivet size when the pressure vessel is subjected to an internal pressure of 500 MPa. Take safety factor = 2. 1.2m A B' A Chope olm 10.5 0.23 hopearrow_forwardContinuity equation A y x dx D T معادلة الاستمرارية Ly X Q/Prove that ди хе + ♥+ ㅇ? he me ze ོ༞“༠ ?arrow_forwardQ Derive (continuity equation)? I want to derive clear mathematics.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY