a) Explanation Draw the given Air standard cycle on P − v and T-s diagram as in Figure (1). b) To determine The back work ratio of the air standard cycle c) To determine The thermal efficiency of the given Air standard cycle

CONNECT FOR THERMODYNAMICS: AN ENGINEERI

9th Edition

ISBN: 9781260048636

Author: CENGEL

Publisher: MCG

See similar textbooks

Concept explainers

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical ener…

Question

Chapter 9.12, Problem 13P

To determine

The sketch of the P−ν and T-s diagrams for the cycle.

To determine

The back work ratio of the air standard cycle

To determine

The thermal efficiency of the given Air standard cycle

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.12, Problem 12P

Chapter 9.12, Problem 14P

Students have asked these similar questions

A gas mixture with a molar analysis of 40% CH4 (methane) and 60% air enters a control volume operating at steady state at location 1 with a mass flow rate of 5 kg/min, as shown in the figure below. Air enters as a separate stream at 2 and dilutes the mixture. A single stream exits with a mole fraction of methane of 5%. Assume air has a molar analysis of 21% O2 and 79% N2. (CH4, Air) m₁ = = 5 kg/min Air (21% O2, 79% N₂) 3 + (5% CH4, 95% Air)

A. Calculate the cutting time if the length of cut is 24 in., the feed rate is 0.030 ipr, and the cutting speed is 80 fpm. The allowance is 0.5 in and the diameter is 8 in. B. Calculate the metal removal rate for machining at speed of 80 fpm, feed of 0.030 ipr, at a depth of 0.625 in. Use data from the previous problem.

Consider 0.65 kg of N2 at 300 K, 1 bar contained in a rigid tank connected by a valve to another rigid tank holding 0.3 kg of CO2 at 300 K, 1 bar. The valve is opened and gases are allowed to mix, achieving an equilibrium state at 290 K. Determine: (a) the volume of each tank, in m³. (b) the final pressure, in bar. (c) the magnitude of the heat transfer to or from the gases during the process, in kJ. (d) the entropy change of each gas and of the overall system, in kJ/K.

Chapter 9 Solutions

CONNECT FOR THERMODYNAMICS: AN ENGINEERI

Ch. 9.12 - What are the air-standard assumptions?Ch. 9.12 - What is the difference between air-standard...Ch. 9.12 - Prob. 3P Ch. 9.12 - How does the thermal efficiency of an ideal cycle,...Ch. 9.12 - How are the combustion and exhaust processes...Ch. 9.12 - What does the area enclosed by the cycle represent...Ch. 9.12 - Prob. 7P Ch. 9.12 - Can the mean effective pressure of an automobile...Ch. 9.12 - What is the difference between spark-ignition and...Ch. 9.12 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The sketch of the P − ν and T-s diagrams for the cycle.

Solution Summary: The author illustrates the sketch of P-nu and T-s diagrams for the air standard cycle.

Concept explainers

The sketch of the P−ν and T-s diagrams for the cycle.

The back work ratio of the air standard cycle

The thermal efficiency of the given Air standard cycle

Want to see the full answer?

Chapter 9 Solutions