Concept explainers
(a)
The final temperature of the steam in tank A.
The final temperature of the steam in tank B.
(a)
Answer to Problem 99RP
The final temperature of the steam in tank A is
The final temperature of the steam in tank B is
Explanation of Solution
Write the expression to calculate the specific volume of saturated water
Here, specific volume of saturated liquid is
Write the expression to calculate the specific internal energy of saturated water
Here, specific internal energy of saturated liquid is
Write the expression to calculate the specific entropy of saturated water
Here, specific entropy of saturated liquid is
Write the expression to calculate the mass from the specific volume.
Write the mass balance equation for the fluid flow process.
Here, mass of the steam entered is
Write the energy balance equation for the entire system considering it as a stationary closed system.
Here, net energy input to the system is
Conclusion:
For Tank A:
Refer the Table A-5 of “Saturated water: Pressure”, obtain the properties of steam at the pressure
Substitute
Substitute
Substitute
Refer the Table A-5 of “Saturated water: Pressure”, obtain the properties of steam at the pressure
Thus, the final temperature of the steam in tank A is
Write the final specific entropy of steam in tank A from isentropic relation.
Substitute
Substitute
Substitute
For Tank B:
Refer to Table A-6 of “Superheated water”, obtain the properties of steam for pressure
Substitute
Substitute
Write the expression to calculate the mass flowing into tank B
Substitute
Calculate the final mass of steam in tank B
Substitute
Write the expression to calculate the final specific volume of steam in tank B from Equation (IV).
Substitute
Substitute
From the Table A-4 of “Saturated water: Temperature”, obtain the properties of water in tank B at specific volume of
Thus, the final temperature of the steam in tank B is
(b)
The amount of work potential wasted during the process.
(b)
Answer to Problem 99RP
The amount of work potential wasted during the process is
Explanation of Solution
Write the entropy generation
Here, entropy input to the system is
Write the expression to calculate the exergy destroyed
Here, the surrounding’s temperature is
Conclusion:
Substitute
Substitute
Thus, the amount of work potential wasted during the process is
Want to see more full solutions like this?
Chapter 8 Solutions
Thermodynamics: An Engineering Approach ( 9th International Edition ) ISBN:9781260092684
- The airplane weighs 144100 lbs and flies at constant speed and trajectory given by 0 on the figure. The plane experiences a drag force of 73620 lbs. 0 a.) If 11.3°, determine the thrust and lift forces = required to maintain this speed and trajectory. b.) Next consider the case where is unknown, but it is known that the lift force is equal to 7.8 times the quantity (Fthrust Fdrag). Compute the resulting trajectory angle and the lift force in this case. Use the same values for the weight and drag forces as you used for part a. 20. YAAY' Farag Ө Fthrust CC + BY NC SA 2013 Michael Swanbom Flift Fweight The lift force acts in the y' direction. The weight acts in the negative y direction. The thrust and drag forces act in the positive and negative x' directions respectively. Part (a) The thrust force is equal to 101,855 ☑ lbs. The lift force is equal to 141,282 ☑ lbs. Part (b) The trajectory angle 0 is equal to 7.31 ✓ deg. The lift force is equal to 143,005 ☑ lbs.arrow_forwardsimply supported beam has a concentrated moment M, applied at the left support and a concentrated force F applied at the free end of the overhang on the right. Using superposition, determine the deflection equations in regions AB and BC.arrow_forwardwhat is heat exchanger, what are formulas, and their importance, define the diagram, and give me a script on how to explain the design of heat exchanger, and how did values end up in that number. based on standards . what is dshellarrow_forward
- FIGURE P1.37 1.38 WP As shown in Figure P1.38, an inclined manometer is used to measure the pressure of the gas within the reservoir, (a) Using data on the figure, determine the gas pressure, in lbf/in.² (b) Express the pressure as a gage or a vacuum pressure, as appropriate, in lbf/in.² (c) What advantage does an inclined manometer have over the U-tube manometer shown in Figure 1.7? Patm = 14.7 lbf/in.² L I C i Gas a Oil (p = 54.2 lb/ft³) 140° 8=32.2 ft/s² 15 in.arrow_forwardwhat is an low pressure Heater, what are formulas, and their importance, define the diagram, and give me a script on how to explain the design of an air preheater, and how did values end up in that number. based on standardsarrow_forwardwhat is an air preheater, what are formulas, and their importance, define the diagram, and give me a script on how to explain the design of an air preheater, and how did values end up in that number. based on standardsarrow_forward
- Qf, Qa,Qm, Qcon,Qfg, Qbd, Qref,Qloss ( meaning, formula, percentage, and importance of higher value na qf, qa etc)arrow_forwardThe beam is supported by a fixed support at point C and a roller at point A. It also has an internal hinge at point B. The beam supports a point load at point D, a moment at point A and a distributed load on segment BC. a. calculate the support reactions at points A and C b. calculate the internal resultant loadings (N, V, M) at points E and F, which lies in the middle between points A and D P = 4 kip Ma = 5 kip-ft w1 = 3 kip/ft and w2 = 4 kip/ft a = 3 ftarrow_forwardFrom the image of the pyramid, I want to find what s1 hat, s2 hat, and s3 hat are. I think s3 hat is just equal to e3 hat right? What about the others?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY