The work and heat transfer for each process.
Answer to Problem 173RP
The heat transfer for the isothermal process 1–2 is
The work done during the process 1-2 is
The work done during the isentropic compression process 2-3 is
The heat transfer for the isentropic process 2–3 is
The work done during constant pressure compression process 3-1 is
The heat transfer during constant pressure compression process 3-1 is
Explanation of Solution
Write the expression to calculate the enthalpy change in process 1-2.
Here, pressure at process 1 is
Write the expression to calculate the ideal gas equation, to find mass of the air.
Here, mass of the air is m , volume at process 1 is
Write the expression to calculate the heat transfer for the isothermal process 1–2.
Here, enthalpy change in process 1-2 is
Write the expression to calculate the work done during the process 1-2
Write the expression to calculate the work done during the isentropic compression process 2-3
Here, mass of the air is m, internal energy at process 3 is
Write the expression to calculate the relative pressure at process 3
Here, relative pressure at process 2 is
Write the expression to calculate the volume at process 3
Write the expression to calculate the work done during constant pressure compression process 3-1
Here, volume at process 3 is
Write the expression to calculate the heat transfer during constant pressure compression process 3-1
Here, heat transfer during constant pressure compression process 3-1 is
Conclusion:
From Table A-1 “the molar mass, gas constant and critical point properties table”, obtain the gas constant
Substitute
Substitute 1.394 kg for m,
Substitute
Thus, the heat transfer for the isothermal process 1–2 is
Substitute
Thus, the work done during the process 1-2 is
From Table A-17, “Ideal-gas properties of air”, obtain the internal energy
Substitute
Refer to Table A-17, “Ideal-gas properties of air”.
Obtain the select the internal energy
Write the formula of interpolation method of two variables.
Here, the variables denoted by x and y are relative pressure and internal energy.
Show relative pressure and internal energy values from the Table A-17.
Relative pressure | Internal energy |
3.481 | 278.93 |
3.696 | ? |
3.806 | 286.16 |
Substitute
The value of internal energy process 1
Show temperature and initial internal energy values from the Table A-17.
Temperature | Internal energy |
3.481 | 390 |
3.696 | ? |
3.806 | 400 |
Substitute
The value of Temperature
Substitute 1.394 kg for m,
Thus, the work done during the isentropic compression process 2-3 is
The heat transfer for the isentropic process 2–3 is zero when entropy change remains unchanged for the isentropic compression process.
Thus, the heat transfer for the isentropic process 2–3 is
Substitute 1.394 kg for m,
Substitute
Thus, the work done during constant pressure compression process 3-1 is
Substitute 37 kJ for
Thus, the heat transfer during constant pressure compression process 3-1 is
Want to see more full solutions like this?
Chapter 7 Solutions
CENGEL'S 9TH EDITION OF THERMODYNAMICS:
- 1) A piston-cylinder device contains 0.3 kg of air initially at 1.8 MPa and 350°C. The air is first expanded isothermally to 500 kPa, then compressed polytropically (with a polytropic exponent of 1.2) to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the boundary work for each process and the net work of the cycle.arrow_forwardFour pounds of steam initially dry and saturated expand isentropically in a non-flow process from an initial pressure of 275 psia to a final pressure of 125 psia. Find its quality and determine the work done in BTU/lb.arrow_forward1. Steam enters a nozzle at 400°C and 800 kPa with a velocity of 10 m/s, and leaves at 300°C and 200 kPa while losing heat at a rate of 25 kW. For an inlet area of 800 cm?, determine the velocity and the volume flow rate of the steam at the nozzle exit. Determine the following: a. Velocity at the exit (m/s) b. Volume flow rate (m³/s) From steam table: h,=3267.7 kJ/kg h,=3072.1 kJ/kg 400°C 300°C 800 kPa Steam v,=0.39429 m /kg 200 kPa v,=1.3163 m /kg 10 m/sarrow_forward
- A piston–cylinder device contains steam that undergoes a reversible thermodynamic cycle. Initially the steam is at 400 kPa and 350C with a volume of 0.3 m3. The steam is first expanded isothermally to 150 kPa, then compressed adiabatically to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the net work and heat transfer for the cycle after you calculate the work and heat interaction for each process.arrow_forwardWater, initially a saturated liquid at 100°C, is contained in a piston-cylinderassembly. The water undergoes a process where it changes to the corresponding saturatedvapor state, during which the piston moves freely in the cylinder. If the change of state isbrought about by heating the water as it undergoes an internally reversible process atconstant pressure and temperature, determine the (a) work and (b) heat transfer per unitmass, each in kJ/kg.arrow_forward3. Initially, 0.55 kg of air is contained in a piston-cylinder device at 2 MPa and 350°C. The air is first expanded isothermally to 500 kPa, then compressed polytropically with a polytropic exponent of 1.2 to the initial pressure, and finally compressed at the constant pressure to the initial state. Determine the heat transfer for each process and the net heat of the cycle (in kJ).arrow_forward
- A piston-cylinder assembly contains 3 lb of water vapor, initially at 300F and 20 lbf/in2 is compressed isothermally to a volume of 14ft3 . The system is then heated at constant volume to a final pressure of 140 lbf/in2 . During the isothermal compression 600 Btu of heat is transferred to the surroundings. Kinetic and potential energy effects are negligible. Show the P-v diagram for both processes, calculate the total work done, and the total change in entropy.arrow_forwardElectrical Engineering A piston-cylinder device contains 0.5 kg of air initially at 3 MPa and 250°C. The air is first expanded at the constant pressure to 0.04 m3, then compressed isothermally to the initial volume, and finally compressed isometrically to the initial state. 1. Draw the P-V diagram. 2. Determine the boundary work for each process and the net work of the cycle. 3. Heat lost during the constant volume process.arrow_forwardA piston-cylinder device initially contains 5 Ibm of liquid water at 20 psia and 70°F. The water is now heated at constant pressure by the addition of 5910.6 Btu of heat. Determine the entropy change of the water during this process.in psi. Select one: a. 6.330 Btu/R b. 8.712 Btu/R c. 5.105 Btu/R d. 7.821 Btu/Rarrow_forward
- An insulated vertical cylinder-piston device contains 0.8 m3 of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is loosened as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m3, at the end of the process. Determine: a) the amount of refrigerant that escaped b) the final temperature of the coolantarrow_forwardA piston-cylinder device contains 5kg of steam at 100 degrees C with a quality of 40%. The steam undergoes the following processes: 1-2 Heat is transferred to the steam in a reversible manner while the temperature is held constant until the steam becomes a saturated vapor. 2-3 The steam expands in an adiabatic, reversible process until the pressure is 40 kPa. Sketch these processes with repect to the saturation lines on a single T-s diagram. Determine the amount of heat transferred to the steam in process 1-2. Determine the work done by the steam in proccess 2-3.arrow_forwardAir in a piston cylinder occupies 0.12 cubic meter at 552 kPa. The air expands in reversible adiabatic process in whichPV^1.4 = C, doing work on the piston until the volume is 0.24 cubic meter. Determine the work of the system.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY