Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
thumb_up100%
Chapter 7, Problem 24R
Why must the reverse flow valve and the flashback arrestor be checked on a regular basis?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the function of On/Off valve?
Which of the following statements is not true?
A direct acting PRV:
Is complex in construction, therefore can malfunction if a very small dirt gets trapped inside the valve, which may result in safety hazard
Offers uneven flow
Does not provide precise pressure control
Causes more wastage of HP compared to a compound one
Which of the following basic system components has the primary function of removing the heat of compression from the air?
Receiver
Relief valve
Pressure regulator
Dryer
Aftercooler
Which of the following statements is true?
A single acting cylinder may have two ports at two different ends and pressurized fluid can be directed to both of them
A single acting cylinder with two ports will can be used as a double acting cylinder
A single acting cylinder may have two ports at two different ends but into only one of the ports pressurized fluid is being directed
A single acting cylinder…
How does a servo valve work?
Chapter 7 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 7 - Using Table 7-1, list the six different fuel gases...Ch. 7 - What metals can be cut with the oxyfuel gas...Ch. 7 - What other term is used to refer to the OFC...Ch. 7 - What is a combination welding and cutting torch?Ch. 7 - State one advantage of owning a combination...Ch. 7 - State one advantage of owning a dedicated cutting...Ch. 7 - What is a mixing chamber? Where is it located?Ch. 7 - Define the term equal-pressure torch. How does it...Ch. 7 - How does an injector-type mixing chamber work?Ch. 7 - State the advantages of having two oxygen...
Ch. 7 - Why are some copper alloy cutting tips...Ch. 7 - Using Table 7-4, answer the following: a . Oxygen...Ch. 7 - What determines the amount of preheat flame...Ch. 7 - What can happen if acetylene is used on a tip...Ch. 7 - Why are some propane and natural gas tips made...Ch. 7 - What types of tip seals are used with cutting...Ch. 7 - If a cutting tip sticks in the cutting head, how...Ch. 7 - How can cutting torch tip seals be repaired?Ch. 7 - What is used to reduce the high cylinder or system...Ch. 7 - What do the two pressure gauges on a regulator...Ch. 7 - Why must the gas pressure be released and the...Ch. 7 - What should be done if the torch flashes back?Ch. 7 - What is the purpose of a reverse flow valve?Ch. 7 - Why must the reverse flow valve and the flashback...Ch. 7 - How can a hose be checked for leaks?Ch. 7 - Why is the oxygen valve turned on before starting...Ch. 7 - Why does the preheat flame become slightly...Ch. 7 - What causes the tiny ripples in a hand cut?Ch. 7 - Why is a slight forward torch angle helpful for...Ch. 7 - Why should cans, drums, tanks, or other sealed...Ch. 7 - Why is the torch tip raised as the cutting lever...Ch. 7 - Why are the preheat holes not aligned in the kerf...Ch. 7 - Sketch the proper end shape of a soapstone that is...Ch. 7 - What are two methods you can use to determine what...Ch. 7 - What is the best way to set the oxygen pressure...Ch. 7 - Why is it important to have extra ventilation...Ch. 7 - What factors regarding a cut can be read from the...Ch. 7 - What is hard slag?Ch. 7 - Why is it important to make good-quality cuts?Ch. 7 - When using an ordinary welding table, what can be...Ch. 7 - Describe the methods of controlling distortion...Ch. 7 - List three things that can become a problem when...Ch. 7 - How does cutting small-diameter pipe differ from...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is meant by regulator creep?arrow_forwardIn a negative backpressure EGR valve, if the exhaust pressure passage in the stem is plugged, the bleed valve remains.arrow_forwardThere can be more than 1 answer per item What is the purpose of having piston ring gaps?So that the temperature from the piston can be easily transferred to the cylinder wallsFor easier overhaul proceduresSo that the piston rings will have allowance in the event of thermal expansionSo that oil can freely enter the system The ideal prototype of the spark-ignition engines, constant volume combustion.Diesel cycleOtto cycleBrayton cycleCarnot cyclearrow_forward
- Why is the shielding gas valve "cracked" before the flow-meter regulator is attached?arrow_forwardWhat may result if a pressure regulator is not used on the type of gas or pressure range for which it was designed?arrow_forwardWhat are the results and discussions in discussing the function of each component of the valve system?arrow_forward
- I8 Which of the following statements regarding relief D. Spring ich of the following statements regarding relief valves is not true? A. A blown fusible plug must be replaced. B. Relief valves should be replaced every five years. C. Relief valves should be vented to the outdoors using a D. Spring-loaded relief valves should be stacked to prevent any leakage. purge line. and ome re reayarrow_forwardWhich of the following is not one of the strokes of a four-cycle engine? Compression Exhaust Intake Ignitionarrow_forwardShould safety valves operating at elevated temperature be open-bonnet (spring-loaded)?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY