Precision Machining Technology
Precision Machining Technology
3rd Edition
ISBN: 9781337795302
Author: Peter, Hoffman.
Publisher: Cengage Learning,
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 6.2, Problem 10RQ

What type of toolholder might he selected for mounting a slitting saw?

Blurred answer
Students have asked these similar questions
! Required information A one-shell-pass and eight-tube-passes heat exchanger is used to heat glycerin (cp=0.60 Btu/lbm.°F) from 80°F to 140°F by hot water (Cp = 1.0 Btu/lbm-°F) that enters the thin-walled 0.5-in-diameter tubes at 175°F and leaves at 120°F. The total length of the tubes in the heat exchanger is 400 ft. The convection heat transfer coefficient is 4 Btu/h-ft²°F on the glycerin (shell) side and 70 Btu/h-ft²°F on the water (tube) side. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the rate of heat transfer in the heat exchanger before any fouling occurs. Correction factor F 1.0 10 0.9 0.8 R=4.0 3.0 2.0.15 1.0 0.8.0.6 0.4 0.2 0.7 0.6 R= T1-T2 12-11 0.5 12-11 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 (a) One-shell pass and 2, 4, 6, etc. (any multiple of 2), tube passes P= T₁-11 The rate of heat transfer in the heat exchanger is Btu/h.
! Required information Air at 25°C (cp=1006 J/kg.K) is to be heated to 58°C by hot oil at 80°C (cp = 2150 J/kg.K) in a cross-flow heat exchanger with air mixed and oil unmixed. The product of heat transfer surface area and the overall heat transfer coefficient is 750 W/K and the mass flow rate of air is twice that of oil. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air Oil 80°C Determine the effectiveness of the heat exchanger.
In an industrial facility, a counter-flow double-pipe heat exchanger uses superheated steam at a temperature of 155°C to heat feed water at 30°C. The superheated steam experiences a temperature drop of 70°C as it exits the heat exchanger. The water to be heated flows through the heat exchanger tube of negligible thickness at a constant rate of 3.47 kg/s. The convective heat transfer coefficient on the superheated steam and water side is 850 W/m²K and 1250 W/m²K, respectively. To account for the fouling due to chemical impurities that might be present in the feed water, assume a fouling factor of 0.00015 m²-K/W for the water side. The specific heat of water is determined at an average temperature of (30 +70)°C/2 = 50°C and is taken to be J/kg.K. Cp= 4181 Water Steam What would be the required heat exchanger area in case of parallel-flow arrangement? The required heat exchanger area in case of parallel-flow arrangement is 1m².

Chapter 6 Solutions

Precision Machining Technology

Ch. 6.2 - Many of the cutters used in machining are made of...Ch. 6.2 - What is the major advantage of using...Ch. 6.2 - Prob. 3RQCh. 6.2 - What type of cutting tool would most likely be...Ch. 6.2 - Which type of cutter would most likely be used to...Ch. 6.2 - What workpiece factors might cause a four-flute...Ch. 6.2 - List three types of milling cutters that are used...Ch. 6.2 - Most manual vertical milling machine spindles are...Ch. 6.2 - A __________ is used to retain the toolholder in...Ch. 6.2 - What type of toolholder might he selected for...Ch. 6.2 - Sketch a corner-rounding endmill.Ch. 6.2 - What toolholding device uses two drive keys and a...Ch. 6.2 - Prob. 13RQCh. 6.2 - List the four basic pieces of a step clamp set: a....Ch. 6.2 - Prob. 15RQCh. 6.2 - Irregularly shaped work may be held in a custom...Ch. 6.3 - List five safety guidelines to observe when...Ch. 6.3 - Briefly describe the process of aligning a milling...Ch. 6.3 - What is chip load?Ch. 6.3 - Define IPM.Ch. 6.3 - Calculate spindle speed and feed for the two...Ch. 6.3 - Briefly describe the process of locating the...Ch. 6.3 - What are two benefits of boring over other...Ch. 6.3 - What are face milling and peripheral milling?Ch. 6.3 - When squaring a block on the vertical mill, what...Ch. 6.3 - What are the three basic methods used to mill...Ch. 6.3 - What must first be done before milling with either...Ch. 6.3 - Prob. 12RQCh. 6.3 - What diameter cutter should be used to create...Ch. 6.3 - When roughing a pocket, should you machine in a...Ch. 6.4 - What is a rotary axis?Ch. 6.4 - Define the term indexing.Ch. 6.4 - Describe the primary differences between the...Ch. 6.4 - Name three types of workpiece features that are...Ch. 6.4 - Briefly describe the two alignment steps that need...Ch. 6.4 - If the outside of a 6"-diameter disk is to be...Ch. 6.4 - What is the gear ratio found in the gear train of...Ch. 6.4 - When using the indexing head, a __________ can be...Ch. 6.4 - A workpiece requires 9 divisions. Calculate the...Ch. 6.4 - In the formula 40D=T,what do T and D represent?
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Hand Tools; Author: UCI Media;https://www.youtube.com/watch?v=4o0tqF0jDdo;License: Standard Youtube License