Concept explainers
Using appropriate measurements and data, explain how to determine the bending stress in the blade.
C6–1
Answer to Problem 6.1CP
The bending stress in the blade is
Explanation of Solution
Given information:
- The steel saw blade passes over the drive wheel of the band saw.
- Use appropriate measurements and data.
Explanation:
The contact area of the cable is upper half portion of the drive wheel. The, the upper half portion of the wheel will undergo stress.
Show the free-body diagram of the drive wheel as in Figure 1.
The force induced in the drive wheel will be uniformly distributed.
The circumferential distance of the circular section is
Convert the semi-circular section into beam section as in Figure 2.
Determine the tension in the cable:
Moment about point A:
Determine the tension in the cable at point B by taking moment about point A.
Along the vertical direction:
Determine the tension in the cable at point A by resolving the vertical component of forces.
Show the calculation of values as follows:
Solve Equation (1).
Substitute
Maximum Bending moment:
The maximum bending moment will occur where the shear force changes sign
Consider a section at a distance x from left end of the beam.
Show the free body diagram of the section as in Figure 3.
Along the vertical direction:
Determine the shear force at the section by resolving the vertical component of forces.
Moment about the section:
Determine the moment at the section by taking moment about the section.
Substitute 0 for V and
Thus, the maximum bending moment will occur at a distance
Substitute
Bending stress:
Calculate the bending stress in the blade using the flexure formula.
Here, c is the distance between the centroid and the extreme fibre and I is moment of inertia of the band saw.
Consider the band saw is in rectangular cross section.
The value of c is
The moment of inertia of the band saw is
Here, b is width of the section and d is depth of the section.
Substitute
Thus, the bending stress in the blade is
Want to see more full solutions like this?
Chapter 6 Solutions
Mechanics of Materials
- Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2000 N-m and a torque of 4300 N-m if the diameter of the hole is equal to 0.7 of the outer diameter of the shaft. The shaft rotates and loads are applied suddenly, with minor shocks. The maximum bending stress is equivalent to 88 N/mm2. Apply ASME Code for this problem.arrow_forwardThe stepped bar has a thickness of 30 mm 90 mm 60 mm 20 mm 7.5 mm 15 mm M M Part A Determine the maximum moment that can be applied to its ends if the allowable bending stress is oallow = 190 MPa Express your answer to three significant figures and include appropriate units. μΑ M = Value Unitsarrow_forwardProblem 1 Please choose the correct answer and also write down your solution. (1) The section supports an upward internal shear force and a clockwise internal torque. Where does the absolute maximum shear stress occur? a. Point A b. Point B c. Point C d. Point D (2) The internal force and moment of the section have been determined as F = 100î + 300k (N) and M = 50î + 40j (N - m). Where does the absolute maximum normal stress occur? a. Point A b. Point B c. Point C d. Point Darrow_forward
- A layshaft is an intermediate shaft within a gearbox that carries gears, but does not carry the primary drive load. It is used to enable variable gear ratios on the output shaft of the gearbox. F₁ Gear Retaining Screw Where: D Gear Driving Key Bearing Lock Nut R₁ 86.0 mm Bearing Driving Key Lay Shaft 111.5 mm 273.0 mm F2 Gear Retaining Ring 75.5 mm F₁-200N F2=35N Determine the Bending Moment and Shear Force diagrams for this layshaft. R₂ Bearing Bearing Lock Nutarrow_forwardDetermine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2000 N-m and a torque of 4300 N-m if the diameter of the hole is equal to 0.7 of the outer diameter of the shaft. The shaft rotates and loads are applied gradually. The maximum bending stress is equivalent to 80 N/mm2. Apply ASME Code for this problem.arrow_forwardDoes the location of the shear center depend upon the applied loading?arrow_forward
- Draw bending moment diagram along with calculations and note the values on the diagramarrow_forwardThe permissible bending stress of a gear material is 150 MPa with a radial load of 100N acting upon it. What is the magnitude of the resultant load acting on the tooth for the given dimensions? 20 30 All dimensions are in mm 8.arrow_forwardDetermine the bending stress at point B and Carrow_forward
- can you solve this?arrow_forwardAn A-36 steel strap having a thickness of 10 mm and a width of 20 mm is bent into a circular arc of radius r = 10 m. Determine the maximum bending stress in the strap.arrow_forwardQu 7 The bar is subjected to a moment of M = 17.5Nm Ifr=5 mm, determine the maximum bending stress in the material. Express your answer in MPa to three significant figures. W h= 86 20 =4 1518 كاء h 20 = 0.25 6max-K =1.5(175 M 2.0 80 mm 7 mm 20 mm мс 1.9 I 1.8 1.7 W 1.6 4 K W 1.5arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY