Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)
10th Edition
ISBN: 9781337399128
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 25RQ
True or False: A two-stage cooling thermostat would be used on a system with one condensing unit.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Why is a low-voltage thermostat normally more accuratethan a high-voltage thermostat?
Question1. If an air conditioning system has three independent zones, how many space thermostats will the system have?
Question 2. A technician is traversing a duct and obtains the following 8 velocity: 500fpm, 400fpm, 375fpm,625fpm,275fpm,360fpm,450fpm,and 575fpm. What is the velocity value that can be used for the system calculations?
What is the primary purpose of a thermostat
jiggle valve?
Select one:
a. To act as a bypass for coolant
b. To relieve water pump pressure
under load
c. To ensure coolant flows the correct
direction
d. To aid in bleeding air from the
system
Chapter 6 Solutions
Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)
Ch. 6 - Why should an air-conditioning technician learn to...Ch. 6 - Briefly explain the layout of a schematic diagram.Ch. 6 - Most schematic diagrams are made up of _____. a....Ch. 6 - Schematic diagrams break the wiring of control...Ch. 6 - Draw the symbols for the following components. a....Ch. 6 - What is the name of an appliance that is used to...Ch. 6 - What is the position of the control switch if the...Ch. 6 - Prob. 8RQCh. 6 - True or False: The evaporator fan motor is...Ch. 6 - What electrical component initiates the defrost...
Ch. 6 - The thermostat of the commercial freezer in Figure...Ch. 6 - What is the purpose of the fan switch in Figure...Ch. 6 - If the temperature in the furnace schematic shown...Ch. 6 - What is the purpose of the transformer in Figure...Ch. 6 - True or False: The system in Figure 6.28 is using...Ch. 6 - The HP and LP switches are connected in __________...Ch. 6 - The contactor is controlled by __________. a. the...Ch. 6 - With the fan switch in the on position, the indoor...Ch. 6 - The compressor and condenser fan motor start...Ch. 6 - The compressor and condenser fan motor are...Ch. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Explain why the lockout relay coil energizes...Ch. 6 - True or False: The first- and second-stage cooling...Ch. 6 - True or False: A two-stage cooling thermostat...Ch. 6 - What is the purpose of the defrost cycle of a heat...Ch. 6 - What two factors initiate the defrost mode in the...Ch. 6 - What type of thermostat is used with the heat pump...Ch. 6 - Explain the operation of the switchover valve and...Ch. 6 - The reversing-valve solenoid is energized on the...Ch. 6 - The defrost cycle of the heat pump schematic in...Ch. 6 - What is a pump-down system and why is it used in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain how microelectromc or electrontc thermostats handle system overshoot and system lag.arrow_forwardExplain the layout and the basic operation of a centralized air conditioning system (or chiller system).arrow_forwardIf the thermostat contacts are closed the compressor and the condenser fan motor are not operating, and all the other loads are operating properly, which might be the problem? A. A bad high pressure safety switch. B. A bad low pressure switch C. Both A. and B. D. A bad thermostatarrow_forward
- Which of the following is true regarding the refrigerantpiping on a rooftop package unit?A. The discharge and liquid lines must be field installed.B. The suction and liquid lines must be field installed.C. The discharge and suction lines must be field installed.D. No refrigerant lines are field installed.arrow_forwardWhich of the following statements is false? The condenser is normally mounted just in front of the radiator. The receiver/dryer is a storage tank for the liquid refrigerant from the condenser. An accumulator is not used in any system with a receiver/dryer. All of the above.arrow_forwardto run d. both a and b 44. Ifa thermostatic expansion valve's thermal bulb came loose from the suction line at the outlet of the evaporator, whích of the following could result? The bulb pressure would increase and the c. thermostatic expansion valve would open. b. The superheat in the evaporator would decrease. a. Liquid refrigerant would flow back to the compressor. d. All of the above are correct. 45. If the thermal bulb assembly develops a leak, what will occur? All of the system's refrigerant will leak a. The valve will open to allow more c. refrigerant to flow. d. It will have no effect on system operation. out. b. The bulb pressure will reduce and the valve will close. 46. The purpose of an externally equalized thermostatic expansion valve is to compensate for excessive evaporator pressure drop b. allow system to equalize faster a. prevent the expansion valve from frosting up d. c. allow refrigerant to expand in the compressor 47. The primary function of an expansion device is…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License