
The final mass of the air in the ballast tank and total heat transfer.

Answer to Problem 177RP
The final mass of air in the ballast tank is
The total heat transfer is
Explanation of Solution
Write the formula for mass of air
Here, the volume of air is
Write the formula for mass of water at initial.
Write the general energy balance equation.
Here, the total energy in is
Refer Equation (IV).
Write the energy balance equation for the system (ballast tank).
Here, the mass is
At final state 2:
The mass of water in the tank is zero. Only air is present in the ballast tank. Hence, the final state energy of the tank is expressed as follows.
At initial state 1:
Both air and water is present in the tank. The initial state energy of the tank is expressed as follows.
The inlet mass of air is expressed as,
Here, the inlet mass is mass of air and the exit mass is mass of water.
Rewrite the Equation (V) as follows.
Refer Table A-4, “Saturated water-Temperature table”.
The enthalpy
It is given that the pressure and temperature of air is kept constant.
The Equation (VI) is reduced as follows.
The specific volume
Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.
The gas constant
Refer Table A-2, “Ideal-gas specific heats of various common gases”.
The specific heat at constant pressure
The specific heat at constant volume
Conclusion:
Here,
Substitute
Substitute
Thus, the final mass of air in the ballast tank is
Substitute
Substitute
Here, the negative sign indicates that the heat is removed.
Thus, the total heat transfer is
Want to see more full solutions like this?
Chapter 5 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
- S.4. Yandaki şekilde AB çubuğu pirinç ve CD çubuğu alüminyumdur. Sıcaklık 20°C iken iki çubuk arasında 0,5 mm boşluk bulunmaktadır. a) Sıcaklık 95°C'ye yükseldiğinde çubuklardaki normal gerilmeleri, b) Bu durumda AB ve CD çubuklarındaki deformasyonu bulunuz. AB çubuğu için: E 105 GPa, a = 20x 10 1/°C CD çubuğu için: E-70 GPa, a 23,6x 106 1/°C 0.5 300 250 mm Alüminyum Çap 50 mm Çap 75 mmarrow_forwardRecall the head loss equation developed in class for a sudden expansion (See section 7.7 in your textbook). h₁= (V1-V2)² 2g Show all the steps in going from this equation to equation 3 for the minor loss coefficient, K, above.arrow_forwardJust do Questions 7, 9, 11. Here are notes attached for reference. I prefer handwritten solutions. ONLY UPLOAD A SOLUTION IF YOU ARE SURE ABOUT THE ANSWER PLEASE. (If you have once answered this question don't answer it again I am looking for a difference solution)arrow_forward
- This is a tilt and rotation question. Here are notes attached for reference. I prefer handwritten solutions. ONLY UPLOAD A SOLUTION IF YOU ARE SURE ABOUT THE ANSWER PLEASE. I prefer handwritten solutions.arrow_forwardHomework#7arrow_forwardHomework#7arrow_forwardQ3. Consider an inlet flow for an engine with a supersonic inlet Mach number as shown in Figure. below, calculate the total pressure loss between point 1 and 3 if the flow passes first an oblique shock wave and then a reflected shock wave. (30 pts) Моо M∞ = 2.0 && = 30°arrow_forwardJust do Questions 7, 9, 11. Here are notes attached for reference. I prefer handwritten solutions. ONLY UPLOAD A SOLUTION IF YOU ARE SURE ABOUT THE ANSWER PLEASE. (If you have once answered this question don't answer it again)arrow_forwardThis is a tilt and rotation question. Here are notes attached for reference. I prefer handwritten solutions. ONLY UPLOAD A SOLUTION IF YOU ARE SURE ABOUT THE ANSWER PLEASE. I prefer handwritten solutions.arrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_iosRecommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill EducationControl Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY