Explanation Refer Fig. P5.21 and Fig. 1. Let the element of volume of the disk be of radius r and thickness dx . Find the equation for radius from the equation of the generating curve. x = h − h a 2 y 2 r 2 = a 2 h ( h − x ) Here, the y component is equal to the radius, h is the radius of the paraboloid, x is the centroid of the element and d x is the thickness of the element. Write the expression for the volume of the element. d V = π r 2 d x = π a 2 h ( h − x ) d x (I) Find the centroid of the element. x E L ¯ = x Here, x E L ¯ is the centroid of the element. Write the expression for the x ¯ for the volume. x ¯ V = ∫ x E L ¯ d V x ¯ = ∫ x E L ¯ d V V (II) Conclusion: Refer Fig.2 Calculate the volume of component 1. V 1 = ∫ 0 h / 2 d V = ∫ 0 h / 2 π a 2 h ( h − x ) d x = π ( a 2 h ) [ h x − x 2 2 ] 0 h / 2 = 3 8 π a 2 h Calculate ∫ 1 x E L ¯ d V for component 1. ∫ 1 x E L ¯ d V = ∫ 0 h / 2 x [ π a 2 h ( h − x ) d x ] = π ( a 2 h ) [ h x 2 2 − x 3 3 ] 0 h / 2 = 1 12 π a 2 h 2 Substitute 1 12 π a 2 h 2 for ∫ 1 x E L ¯ d V and 3 8 π a 2 h for V 1 in equation (II). x 1 ¯ = 1 12 π a 2 h 2 3 8 π a 2 h = 2 9 h Thus, the value of x ¯ for the first component is 2 9 h

12th Edition

ISBN: 9781260804638

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventi…

Videos

Question

Chapter 5.4, Problem 5.124P

To determine

To determine the value of x¯ for the two volumes.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 5.4, Problem 5.123P

Chapter 5.4, Problem 5.125P

Students have asked these similar questions

answer this as soon as possible, please.

A piston–cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.26 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the piston rises 20 cm more. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the work done during this process. The work done during this process is kJ.

A 4-m × 5-m × 7-m room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h, and a 100-W fan is used to distribute the warm air in the room. The rate of heat loss from the room is estimated to be about 5000 kJ/h. If the initial temperature of the room air is 10°C, determine how long it will take for the air temperature to rise to 25°C. Assume constant specific heats at room temperature. The gas constant of air is R = 0.287 kPa·m3/kg·K (Table A-1). Also, cv = 0.718 kJ/kg·K for air at room temperature (Table A-2). Steam enters the radiator system through an inlet outside the room and leaves the system through an outlet on the same side of the room. The fan is labeled as W sub p w. The heat is given off by the whole system consisting of room, radiator and fan at the rate of 5000 kilojoules per hour. It will take 831 Numeric ResponseEdit Unavailable. 831 incorrect.s for the air temperature to rise to 25°C.

Chapter 5 Solutions

VECTOR MECHANICS FOR ENGINEERS W/CON >B

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

the value of x ¯ for the two volumes.

Solution Summary: The author explains how to determine the value of stackrel x for the two volumes.

Concept explainers

Videos

To determine the value of x¯ for the two volumes.

Want to see the full answer?

Chapter 5 Solutions