Concept explainers
(a)
Interpretation:
The average translational kinetic energy of the two given gases has to be compared.
Concept introduction:
The average translational energy of an ideal gas depends only on the gas temperature and don’t depend of the quantity of the gas.
(b)
Interpretation:
The partial pressure of the two given gases in the mixture has to be compared.
Concept introduction:
An ideal gas in a mixture of gases enclosed in a rigid container will occupy the whole volume of the container when the other gases are not present, that is the partial pressure of the gas is equal to the pressure which the gas will exert if it is present alone in the container. Therefore, the
(c)
Interpretation:
The mole fraction of the two given gases in the mixture has to be compared.
Introduction:
The mole fraction of an ideal gas in a mixture of gases is simply equal to the ratio of the partial pressure of the gas to the total pressure in the system. The total pressure of the system is equal to the sum of the partial pressures of the gases.
(d)
Interpretation:
The rate of effusion of the two given gases has to be compared.
Introduction:
The rate of effusion of a gas can be calculated using Graham’s law of diffusion. As per Graham’s law, the rate of effusion of a gas has inverse relation with mass of the gas taken, that is
Where w is the mass of the gas taken.
Want to see the full answer?
Check out a sample textbook solutionChapter 5 Solutions
PRINCIPLES+REACTIONS
- Choose a number and match the atomic number to your element on the periodic table. For your element, write each of these features on a side of your figure. 1. Element Name and symbol 2. Family and group 3. What is it used for? 4. Sketch the Valence electron orbital 5. What ions formed. What is it's block on the periodic table. 6. Common compounds 7. Atomic number 8. Mass number 9. Number of neutrons- (show calculations) 10. Sketch the spectral display of the element 11.Properties 12. Electron configuration 13. Submit a video of a 3-meter toss in slow-moarrow_forward[In this question, there are multiple answers to type in a "fill-in-the-blank" fashion - in each case, type in a whole number.] Consider using Slater's Rules to calculate the shielding factor (S) for the last electron in silicon (Si). There will be electrons with a 0.35 S-multiplier, electrons with a 0.85 S-multiplier, and electrons with a 1.00 S-multiplier.arrow_forwardProvide the unknown for the given data.arrow_forward
- Draw the Lewis structures of two methanol (CH3OH) molecules and depict hydrogenbonding between them with dashed lines. Show all lone pairs. Provide a thorough analysis to apply concept idea into other problems.arrow_forwardSteps and explanation please.arrow_forwardHow could you distinguish between each pair of compounds below using IR? For each pair citeone bond and it’s frequency that you could use to distinguish between them. Please provide thorough analysis to apply into further problems.arrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistry: An Atoms First ApproachChemistryISBN:9781305079243Author:Steven S. Zumdahl, Susan A. ZumdahlPublisher:Cengage Learning
- Chemistry for Engineering StudentsChemistryISBN:9781337398909Author:Lawrence S. Brown, Tom HolmePublisher:Cengage LearningChemistry: Principles and PracticeChemistryISBN:9780534420123Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward MercerPublisher:Cengage LearningChemistry: Matter and ChangeChemistryISBN:9780078746376Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl WistromPublisher:Glencoe/McGraw-Hill School Pub Co