Concept explainers
(a)
To rewrite:
In dimensionless parameters, using the pi theorem.

Answer to Problem 5.3CP
The dimensionless function is
Explanation of Solution
Given Information:
Reference Prob 4.8:
Oil of viscosity
Concept Used:
The number of pi groups are to be calculated:
Where k is the number of variables and r is the number of fundamental references.
On substituting 6 for k and 3 for r ,
Calculation:
Dimensional analysis is applied to find the pi groups.
First pi group:
Where
On substituting
On equating M coefficients:
On equating T coefficients:
On equating L coefficients:
Hence, a = 0, b = -1/2 and c = -1/2
Therefore, the first pi group is as follows:
Second pi group:
Where
On substituting
On equating M coefficients:
On equating T coefficients:
On equating L coefficients:
Therefore, the second pi group is as follows:
Third pi group:
Where
On substituting
On equating M coefficients:
On equating T coefficients:
On equating L coefficients:
Hence, a = 0, b = 0 and c=- 1
Therefore, the pi group is as follows:
Hence, as per the choices:
On substituting
Hence, the dimensionless function is
Conclusion:
The dimensionless function is
(b)
To verify:
That the exact solution from Prob 4.8 is consistent with the result in part (a).

Answer to Problem 5.3CP
The exact solution from Prob 4.8 is consistent with the result in part (a).
Explanation of Solution
Given Information:
Reference Prob 4.8:
Oil of viscosity
Concept Used:
The exact solution obtained from prob 4.8 is to be considered:
Calculation:
Hence, the exact solution from Prob 4.8 can be expressed in terms of dimensionless function.
Conclusion:
The exact solution from Prob 4.8 is consistent with the result in part (a).
Want to see more full solutions like this?
Chapter 5 Solutions
Fluid Mechanics, 8 Ed
- 2. A single crystal of aluminum is oriented for a tensile test such that its slip plane normal makes an angle of 28.1° with the tensile axis. Three possible slip directions make angles of 62.4°, 72.0°, and 81.1° with the same tensile axis. (a) Which of these three slip directions is most favored? (b) If plastic deformation begins at a tensile stress of σ x = 1.95 MPa (280 psi), determine the critical resolved shear stress for aluminium. (c) If this single crystalspecimen is loaded under the new stress state: σ x =1.2 MPa σ y = -0.8 MPa, and τ xy = 0.6 MPa, howmuch is the resolve the shear stress along the most favored slip direction?arrow_forwardPlease explain how to do each part and tell me if my drawing is correct. thank youarrow_forward4. Determine which of the following flow fields represent a possible incompressible flow? (a) u= x²+2y+z; v=x-2y+z;w= -2xy + y² + 2z a (b) V=U cose U coso 1 (9) [1-9] Usino |1 (4)] [+] V=-Usin 1+1arrow_forward
- 3. Determine the flow rate through the pipe line show in the figure in ft³/s, and determine the pressures at A and C, in psi. 5' B C 12° 20' D 6"d 2nd- Water Aarrow_forward5. A flow is field given by V = x²₁³+xy, and determine 3 ·y³j- (a) Whether this is a one, two- or three-dimensional flow (b) Whether it is a possible incompressible flow (c) Determine the acceleration of a fluid particle at the location (X,Y,Z)=(1,2,3) (d) Whether the flow is rotational or irrotational flow?arrow_forwardSolve this problem and show all of the workarrow_forward
- Solve this problem and show all of the workarrow_forwarddraw the pneumatic circuit to operate a double-acting cylinder with: 1. Extension: Any of two manual conditions plus cylinder fully retracted, → Extension has both meter-in and meter-out, 2. Retraction: one manual conditions plus cylinder fully extended, → Retraction is very fast using quick exhaust valve.arrow_forwardCorrect answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you. Expert solution plsarrow_forward
- Correct answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you.arrow_forwardCorrect answer is written below. Detailed and complete solution with fbd only. I will upvote, thank you.arrow_forwardCorrect answer is written below. Detailed and complete solution only with fbd. I will upvote, thank you.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





