Heating Ventilating and Air Conditioning: Analysis and Design
Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 5, Problem 5.22P

Determine the overall heattransfer coefficient for (a) an ordinary vertical single-glass window with thermal break. (b) Assume the window has a roller shade with a 3 1 2 in. (89 mm) air space between the shade and the glass. Estimate the overall heat-transfer coefficient.

Blurred answer
Students have asked these similar questions
1. A composite furnace wall is made up of a 12-in. lining of magnesite refractory brick, a 5-in.thickness of 85% magnesia, and a steel casing 0.10-in. thick. Flue gas temperature is 2200 F andthe boiler room is at 80 F. Gas side film coefficient is 15 Btu/hr-sq.ft-F and air side is 4.0.Determine:a. The thermal current Q/Ab. Interface temperaturesc. Effect on thermal current and inside refractory wall temperature if the magnesia insulation weredoubled.
(a) Find the refrigeration capacity if no insulation is used for the walls and ceiling. (b) Select insulation(s) for the wall and ceiling to reduce the refrigeration capacity. Evaluate the thickness required for the insulation you selected to reduce the refrigeration load by approximately 30%. (c) Add a 1m x 1m window glass to the room. Use the data collected from previous parts. Assume the internal surroundings surfaces (e.g., walls and ceilings) have the same temperature as the inside temperature, and the external surroundings (landscape, buildings, etc.) are also at the same temperature as the outside temperature. Assume the convection coefficients between air (internal and external) and the glass are the same as the walls and the air. If the glass has an emissivity of 0.9, calculate the rate of heat loss through the glass. Assume steady-state conditions, negligible temperature gradients in the glass, and both inner and outer surfaces exposed to large surroundings.
A composite wall is formed of a 2.5 cm copper plate, a 3.2 mm layer of asbestos,and a 5 cm layer of fiberglass. The wall is subjected to an overall temperaturedifference of 560oC. Calculate the heat flux through the composite structure.

Chapter 5 Solutions

Heating Ventilating and Air Conditioning: Analysis and Design

Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License