Concept explainers
Complete each line of the following table on the basis of the conservation of energy principle for a closed system.
Qin kJ |
Wout kJ |
E1 kJ |
E2 kJ |
m kg |
e2 – e1 kJ/kg |
280 | — | 1020 | 860 | 3 | — |
−350 | 130 | 550 | — | 5 | — |
— | 260 | 300 | — | 2 | −150 |
300 | — | 750 | 500 | 1 | — |
— | −200 | — | 300 | 2 | −100 |
FIGURE P4–29
Fill the blanks from the below table on the basis of the conservation of energy principle for a closed system.
280 | 1020 | 860 | 3 | ||
130 | 550 | 5 | |||
260 | 300 | 2 | –150 | ||
750 | 500 | 1 | |||
300 | 2 |
Explanation of Solution
Write the energy balance equation for closed system.
Here, energy transfer in to the control volume is
Substitute
Here, amount of heat transfer into the system is
Substitute
Here, initial and final internal energy are
Conclusion:
For row I
Substitute
Substitute
For row II
Substitute
Substitute
For row III
Substitute
Substitute
For row IV
Substitute
Substitute
For row V
Substitute
Substitute
The following table blanks are filled and are shown below as summarized.
280 | 1020 | 860 | 3 | ||
130 | 550 | 5 | |||
260 | 300 | 2 | –150 | ||
750 | 500 | 1 | |||
300 | 2 |
Want to see more full solutions like this?
Chapter 4 Solutions
THERMODYNAMICS LLF W/ CONNECT ACCESS
- FN: 76arrow_forwardPlease solve this question, Thank you very much.arrow_forwardThree forces are applied to the beam. F2 = (-200 + 600 ĵ -250 K) N. Z F2 d3. d2 HD d1 F1 F3 + Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ 250 N F3 400 N d₁ 1 m d2 4 m d3 0.5 m a. Replace the force system with an equivalent force, FR , express as a cartesian vector. b. Replace the force system with an equivalent couple moment acting at point O, (MR)o, express as a cartesian vector. Round your final answers to 3 significant digits/figures. F = R (MR)O = m + 2 + 2 + k) N ) N-arrow_forward
- 2. What is the equivalent stiffness of the system of Fig. 1-19 using the displacement of the block as the generalized coordinate? E = 210 x 10 x 10ʻ N 1= 1.5 x 10 mª 2.5 m 2 x 10 N 3 x 10 N Fig. 1-19 Answer: 4,690,000 N/Marrow_forwardDraw the free body diagram of the following figure:arrow_forwardAn elastic string is fixed at one end and is wound on a drum of diameter 0.2m so that the tension in the string increases as the angle through which the drum turns increases. The torque Ton the drum then varies according to the law: T = Sr20 where S = stiffness of elastic string (S=120KN/m) r = radius of drum As the drum starts at 0 = 0, the work done can be calculated using calculus, for any given value of 0, as shown: ST de Determine the work done by the drum if it rotates through an angle of 0 = 2/3,arrow_forward
- 1.75m 1.5 m 2.75m Given: G/0 Find: 2.25m 6 o B 2.0m . h = 2.05 meters • Tension = 85 Newtons 26 1.5m W Magnitude of internal axial force (Newtons) Axial Force Bending moment V Shear forcearrow_forwardDetermine the equivalent spring stiffness constant of the following spring in series and parallel. 250 N/m 175 N/m ww 80 N/m Farrow_forwardA Texas rancher wants to fence off his four-sided plot of flat land. He measures the first three sides, shown as A, B, and C in the figure below, where 44.411 km and = 749, y+A+B+C + D = 0 N C-3.02 km D-7 km D 9- /0= ? с 75 A = 4.40 km 24° A B 16° W S B=2.48 km E He then correctly calodates the length in kilometers and orientation in degrees west of south of the fourth side D. What is his rasul in kilometers and degrees west of south7 kom * west of southarrow_forward
- Give True or False for the following: 1.In liquids and gases, heat transmission is caused by conduction and convection 2.The surface geometry is the important factor in convection heat transfer 3. The heat transfer by conduction from heated surface to the adjacent layer of fluid, 4. The heat transfer is increased in the fin when &> 1 5.The unit of the thermal diffusivity is m²/s 6. Temperature change between the materials interfaces is attributed to the thermal contact resistance 7. A material that has a low heat capacity will have a large thermal diffusivity. 8. Heat conduction flowing from one side to other depends directly on thickness 9.Fin efficiency is the ratio of the fin heat dissipation with that of no fin 10.The critical radius is represented the ratio of the convicted heat transfer to the thermal conductivityarrow_forwardThe beam is supported by rods AB and CD that have different cross-sectional areas. The area of rod AB is AAB = 10 mm² .The area of rod CD is Acp = 8.25 mm². B F₁ Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ d₁ d₂ NAB= 5050 N 3.25 mm 0.5 mm a. Determine the magnitude of the normal internal force in rod CD, NCD. b. Determine the magnitude of the normal internal force in rod AB, NAB. c. Determine the normal stress in rod CD, OCD. d. Determine the normal stress in rod AB, O AB. Round your final answers to 3 significant digits/figures. NCD = N Narrow_forwardvertica lues of x shown in the diagram. Even if a segment is 50 lb/ft 20 ft A V (lb) 600 500 400 300 *********** con 10 ft 80 lb 90000 I all 200 lb-ft Farrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning