Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 45, Problem 17RQ
To determine
To fill:
The appropriate word in the given sentence.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Choose correct answer:
The purpose of a capillary tube in a refrigeration system is to ___________
A.
Reduce the pressure and not temperature
B.
Reduce the temperature and pressure
C.
Increase the temperature and pressure
D.
Reduce the temperature and not pressure
7)
With the aid of drawing and labels, discuss the operation of the following instruments used to measure volumetric flow:
a. Rotary disk meter
b.Rotary displacement meter
c.Revolving drum condensate meter
d.Piston meter
e. Bellow Gas meter
Chapter 45 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 45 - The typical temperature inside the fresh-food...Ch. 45 - The operating condition for the single compressor...Ch. 45 - When the air temperature in a domestic freezer is...Ch. 45 - Typical head pressures should correspond to a...Ch. 45 - Using the temperature/pressure chart in Unit 3,...Ch. 45 - Using the pressure/temperature chart in Unit 3,...Ch. 45 - If a forced-draft evaporator fan motor is wired in...Ch. 45 - Frost accumulates on the evaporators of...Ch. 45 - The defrost cycle in a domestic refrigerator may...Ch. 45 - Prob. 10RQ
Ch. 45 - What are the two types of evaporators found in...Ch. 45 - Refrigerators currently being manufactured in the...Ch. 45 - Condensers in these refrigerators are...Ch. 45 - Home freezers are air-cooled and may have...Ch. 45 - Induced-draft condensers are typically used with...Ch. 45 - The capillary tube metering device is usually...Ch. 45 - Prob. 17RQCh. 45 - If the compressor has liquid refrigerant returning...Ch. 45 - Some freezers may have ______heaters to prevent...Ch. 45 - Welded ______sealed compressors are normally used...Ch. 45 - Special heaters called ______heaters are often...Ch. 45 - Prob. 22RQCh. 45 - Prob. 23RQCh. 45 - The adjustment device used for low atmospheric...Ch. 45 - Prob. 25RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The capillary tube metering device is usually fastened to the______for heat exchange. A. suction line B. compressor discharge line C. liquid linearrow_forwardHow is expansion in hot water pipes handled?arrow_forwardQuestions Steam from the turbine exhausts directly into the (shell/water) of the 1. condenser. 2. As the steam flows down over the tube bundles it gives up (a) point, where it becomes liquid again. until it reaches the (b) 3. True or False a. The main steam condenser for a turbine is usually located below the turbine. b. One routine maintenance procedure frequently done inside a condenser is plugging tubes to clear them of blockage. 4. Name two safety precautions that must be taken before work may be safely performed inside the water boxes of a condenser. a. b. One way of keeping a unit of line if tube leakage is discovered while the unit is in service is the introduction of a biodegradable substance such as to the cooling water. 5.arrow_forward
- Choose correct answer: In a condenser, the vacuum is found to be 2 N/cm2. The barometer reads 735 mm of Hg, then its approximate absolute pressure is ____________ A. 786.47 kPa B. None of the answers given C. 0.078647 N/mm2 D. 786470 N/m2arrow_forwardWhat is the unit of flow rate?arrow_forwardName and briefly describe the six classes of leaks.arrow_forward
- The approach temperature for the evaporator isA. the difference between the suction and head pressuresconverted to temperature.B. the difference between the refrigerant boiling temperatureand the suction-line temperature.C. the difference between the refrigerant boiling temperatureand the inlet water temperature.D. the difference between the refrigerant boiling temperatureand the leaving-water temperature.arrow_forwardDefine the Pipe and Duct Flow?arrow_forwardindustrial application of fire tube and water tube boilerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License