Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 43, Problem 9RQ
A machine delivered for installation has a 2-inch pulley on the motor and a 6-inch pulley on the load. The motor nameplate reads 180 rpm. At what speed in rpm will the driven machine rotate?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A 1750 rpm motor has a 3” pitch diameter drive pulley. It is driving a 9” pitch diameter pulley. What would be the rpm of the driven pulley?
A belt-driven blower assembly is equipped with a motorthat turns a 5-in. drive pulley at a speed of 3450 rpm.The blower is turning at a speed of 1725 rpm. Determinethe size of the driven pulley.
Belt drives have small pulleys 250 mm in diameter with a wrap angle of 120 degrees. The diameter of the large pulley is 500 mm. What is the distance between the axles of the two pulleys?
Chapter 43 Solutions
Understanding Motor Controls
Ch. 43 - What are the disadvantages of low-speed, directly...Ch. 43 - Prob. 2RQCh. 43 - What three alignment checks should be made to...Ch. 43 - Prob. 4RQCh. 43 - Induction motors should not be used below a...Ch. 43 - What is the primary reason for using a pulley...Ch. 43 - How tightly should V-belts be adjusted?Ch. 43 - Refer to Figure 436 and assume the motor is to...Ch. 43 - A machine delivered for installation has a 2-inch...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Can someone please help me to solve the following question showing all work. Thank youarrow_forwardQ- The reduction of speed from 360 rpm to 120 rpm is desired by the use of a chain drive. The driving sprocket has 18 teeth. What is the number of teeth on the driven sprocket?arrow_forwardMechanism designarrow_forward
- A belt-driven blower assembly is equipped with a motor that turns a 5-in. drive pulley at a speed of 3450 rpm. The blower is turning at a speed of 1725 rpm. Determine the size of the driven pulley.arrow_forwardDriver Pulley 1 is 10” in diameter, runs at 1200 RPM, and supplies 2.5 ft-lbs of torque. Pulley 2 (driven) is 32” in diameter. What is the output torque of Pulley 2? What is the output speed of Pulley 2?arrow_forwardA bucket elevator has a head pulley diameter of 14 inches. There are 260 buckets having a size of 4 in wide and 6 in long attached to its belt at 1 ft spacing. What will be its recommended rpm and the speed in number of buckets per minute?arrow_forward
- 3. A motor has pinion gear with 14 teeth and is meshed with a gear with 52 teeth. The gear is attached to a shaft that drives an 85mm diameter wheel. If the motor spins at 1750rpm's, what is the speed of the vehicle in m/s?arrow_forwardShaft A with 12 inches diameter pulley running at 250 rpm is connected to shaft B by means of 26 inches diameter pulley. Another pulley on shaft B 16 inches diameter is connected to 10 inches diameter pulley on shaft C. Find the speed of shaft C.arrow_forwardDerive the expressions for A, B, & C in the given figure with the help of clear drawing and stepwise procedure. Also find the expression for the Length of the belt drives for open and closed belt drives.arrow_forward
- Mechanismarrow_forwardTwo pulleys are run by a common belt. If a 10.8 inch diameter pulley turns at 900 rpm, what is the diameter of the second pulley if it turns at 421 R.P.M.? Note: Speed is inversely proportional to diameter.arrow_forward5) In the mechanism below block ( I ) is driven by the power transmission screw. Get a degree of freedom.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License