Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 40, Problem 8ASRQ
Technician A says that when a car is moving straight ahead, all differential gears rotate as a unit. Technician B says that when a car is turning a corner, the inside differential side gear rotates slowly on the pinion, causing the outside side gear to rotate faster. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that a hunting gearset is one inwhich one drive pinion gear tooth contacts only certainring gear teeth. Technician B says that a partialnonhunting gearset is one in which one pinion toothcontacts only six ring gear teeth. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
Technician A says that a Simpson gearset is two planetary gearsets that share
a common sun gear. Technician B says that a Ravigneaux gearset has two
sun gears, two sets of planet gears, and a common ring gear. Who is
correct?
a.Technician A only
b.Technician B only
c.Both A and B
d.Neither A or B
Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Chapter 40 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardWhen an idler gear is placed between the driving and driven gears, the driven gear:a. rotates the opposite direction as the drive gearb. rotates the same direction as the drive gearc. reduces the torque transfer from the drivegear to the driven geard. none of the abovearrow_forwardTechnician A says that a hunting gearset is one in which one drive pinion gear tooth contacts only certain ring gear teeth, Technician B says that a partial nonhunting gearset is one in which one pinion tooth contacts only six ring gear teeth. Who is correct?arrow_forward
- 2. When inspecting a transaxle's gears, be Technician A says that a shiny wear pattern on the center of the gear teeth is normal. Technician B says that it is normal for a reverse idler gear to have small chips on its engagement side. Who is correct? A. A only C. Both A and B В. В only D. Neither A nor Barrow_forwardWhen discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?arrow_forwardWhen discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
- Tech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?arrow_forwardWhen a transmission is described as having two planetary gearsets in tandem, what does this mean?arrow_forwardWhile discussing a Lepelletier system: Technician A says that two simple planetary gearsets are connected in tandem. Technician B says that these systems rely on various combinations of the planetary gears to obtain many forward gears. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which type of gear is more likely to develop gear whine at higher speeds? a. rotates in the same direction as the driving gear b. rotates in the opposite direction of the driving gear c. remains stationaryarrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardWhich type of gear develop gear whine at high rotational speed? a.Spur gear b.Helical gear c.Both a and b d.Neither a nor barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License