Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 40, Problem 5RQ
What basic criteria should be considered in designing jigs and fixtures?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
1) What does the specification "8.8" in the standard designation of a bolt mean? Specify values including units.
2) Name two groups of standards in addition to national, industry-wide standards and where they are valid.
3) Which three options exist for defining dimensional tolerances in a technical drawing?
With a neat sketch explain shaper machine and its parts?
#3?
Chapter 40 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 40 - What are the two primary functions of a...Ch. 40 - Prob. 2RQCh. 40 - An early treatise defined a jig as a device that...Ch. 40 - Does an ordinary vise qualify as a fixture? Why or...Ch. 40 - What basic criteria should be considered in...Ch. 40 - In any part drawing, what are the critical...Ch. 40 - What difficulties can result from not keeping...Ch. 40 - Prob. 8RQCh. 40 - Which of the basic design principles relating to...Ch. 40 - What are the two reasons for not having drill...
Ch. 40 - Why does the use of down milling often make it...Ch. 40 - Prob. 12RQCh. 40 - A large assembly jig for an airplane-wing...Ch. 40 - Explain why the use of a given fixture may not be...Ch. 40 - Prob. 15RQCh. 40 - In the clamps shown in Figure 40.20, what is the...Ch. 40 - What are other common types of clamp?Ch. 40 - What is the purpose of dimensioning the...Ch. 40 - Prob. 19RQCh. 40 - In Figure 49.9. why arent there three points put...Ch. 40 - Which set of locators in Figure 49.9 establishes...Ch. 40 - What are the four stages of the SMED methodology...Ch. 40 - Prob. 23RQCh. 40 - How could the intermediate jig concept be used in...Ch. 40 - Develop a sequence of operations to produce the...Ch. 40 - Suppose in the sample problem at the end of this...Ch. 40 - Notice that the holes in the part in Figure 49.9...Ch. 40 - Prob. 6PCh. 40 - A part has two holes located for drilling by...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Please answer this question,it really important for mearrow_forwardIndicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of Pd is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4µm. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 pm.arrow_forwardWhat is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the assembly of an external and an internal feature of size of the same type, 3) the algebraic difference between the limit size and the nominal size.arrow_forward
- Which is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?arrow_forwardSTATICS : METHOD OF SECTIONS - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - I PROVIDED A SAMPLE PROBLEM SO THAT YOU WILL KNOW HOW TO SOLVE IT. THANK YOU IN ADVANCE! Solve the forces in PQ, FL, QG, and QM. Hint: Identify all zero-force members and remove them from the structure. In the summation of moments, look for a point where member forces at the supports converge so that their moment arm is zero. From here you will be able to solve PQ. Solve FL using summation of moments from the other half of the section. Solve QG and QM using Method of Joints.arrow_forwardTandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing stage OIt is not possible to reduce at one stage O Annealing is needed between stages Accuracy in dimensions is not possible otherwise Which of the following abrasive materials is most appropriate for grinding nonferrous metals? Silicon carbide O Aluminum oxide Cubic boron nitride Diamondarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License