Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Question
Chapter 40, Problem 19RQ
To determine
The reason for part sitting on locator buttons and not resting on the flat plate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Refer to the figure below. Read the feature control frame in the figure and write it out below.
0.010MABMCM
I need an answer quickly please.
what is the omega value?
as per the professor, the IC is at b not a
Chapter 40 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 40 - What are the two primary functions of a...Ch. 40 - Prob. 2RQCh. 40 - An early treatise defined a jig as a device that...Ch. 40 - Does an ordinary vise qualify as a fixture? Why or...Ch. 40 - What basic criteria should be considered in...Ch. 40 - In any part drawing, what are the critical...Ch. 40 - What difficulties can result from not keeping...Ch. 40 - Prob. 8RQCh. 40 - Which of the basic design principles relating to...Ch. 40 - What are the two reasons for not having drill...
Ch. 40 - Why does the use of down milling often make it...Ch. 40 - Prob. 12RQCh. 40 - A large assembly jig for an airplane-wing...Ch. 40 - Explain why the use of a given fixture may not be...Ch. 40 - Prob. 15RQCh. 40 - In the clamps shown in Figure 40.20, what is the...Ch. 40 - What are other common types of clamp?Ch. 40 - What is the purpose of dimensioning the...Ch. 40 - Prob. 19RQCh. 40 - In Figure 49.9. why arent there three points put...Ch. 40 - Which set of locators in Figure 49.9 establishes...Ch. 40 - What are the four stages of the SMED methodology...Ch. 40 - Prob. 23RQCh. 40 - How could the intermediate jig concept be used in...Ch. 40 - Develop a sequence of operations to produce the...Ch. 40 - Suppose in the sample problem at the end of this...Ch. 40 - Notice that the holes in the part in Figure 49.9...Ch. 40 - Prob. 6PCh. 40 - A part has two holes located for drilling by...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the workpiece.arrow_forwardA programmable indexing fixture creates a fourth axis called a ________ __________ that is similar to a rotary table used on a manual milling machine.arrow_forwardI need the answer as soon as possiblearrow_forward
- HYDRAULICS & ELECTRO-HYDRAULICSarrow_forwardK/s docs.google.com/forms öslg äbäi The command using to insert * :seal is إجابتك نقطة واحدة The main part in the screw * :connection is Screw O Nut Hole Washer 3alg äbäi The command using to insert * :center line is إجابتك ...arrow_forwardWhile constructing a building, an engineer need to fix two steel beams together using a bracket as shown in Figure 1. Using absolute coordinate system, construct a G-code program for drilling hole number 2 only. To remove the metal chips the hole should be done in two equal steps. During the drilling, coolant should be on after spindle starts and stop before spindle stops. The spindle speed set to 1750 RPM. Drilling bit in rack number 2 and it should be 2 mm over the work piece. Drilling feed rate is 25 mm/min. Explain each code used in the program in a column. 57.5- 12.5 Hole (4) Hole (3) 30 10 Hole (2) Hole (1) X0 YO ZO 10 15 All dimensions shown are in mm Figure 1arrow_forward
- How did you get the Tsat valuesarrow_forwardWhich of the following settings does not allow you to control point specifications?a. Grid b. Snap c. Ortho d. Polararrow_forwardWrite and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as; 1. Crank-rocker mechanism; 2. Drag link mechanism; 3. Double rocker mechanism; 4. Crossover-position or charge-point mechanism; 5 Triple rocker mechanism (non-grashof). Use technical Pen for the following: 0.2(light -for linkages and hand writing), 0.4(medium - for joints), 0.6(heavy - for fixed link or frames) use 2-4-4 template, all caps, italicized.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License