DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 40, Problem 5RQ
What basic criteria should be considered in designing jigs and fixtures?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
With a neat sketch explain shaper machine and its parts?
Please answer this question,it really important for me
Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing.
Discuss a specific feature in a specific product/design case where calling out this geometric tolerance would be relevant for performance, assembly, or general operation.
Chapter 40 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 40 - What are the two primary functions of a...Ch. 40 - Prob. 2RQCh. 40 - An early treatise defined a jig as a device that...Ch. 40 - Does an ordinary vise qualify as a fixture? Why or...Ch. 40 - What basic criteria should be considered in...Ch. 40 - In any part drawing, what are the critical...Ch. 40 - What difficulties can result from not keeping...Ch. 40 - Prob. 8RQCh. 40 - Which of the basic design principles relating to...Ch. 40 - What are the two reasons for not having drill...
Ch. 40 - Why does the use of down milling often make it...Ch. 40 - Prob. 12RQCh. 40 - A large assembly jig for an airplane-wing...Ch. 40 - Explain why the use of a given fixture may not be...Ch. 40 - Prob. 15RQCh. 40 - In the clamps shown in Figure 40.20, what is the...Ch. 40 - What are other common types of clamp?Ch. 40 - What is the purpose of dimensioning the...Ch. 40 - Prob. 19RQCh. 40 - In Figure 49.9. why arent there three points put...Ch. 40 - Which set of locators in Figure 49.9 establishes...Ch. 40 - What are the four stages of the SMED methodology...Ch. 40 - Prob. 23RQCh. 40 - How could the intermediate jig concept be used in...Ch. 40 - Develop a sequence of operations to produce the...Ch. 40 - Suppose in the sample problem at the end of this...Ch. 40 - Notice that the holes in the part in Figure 49.9...Ch. 40 - Prob. 6PCh. 40 - A part has two holes located for drilling by...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What can you do to make parts fit without having to recut or regrind them?arrow_forwardEstimate the manufacturing cost for a simple machined component: a. Compare the costs for manufacturing volumes of 1, 10, 100, 1000, and 10,000 pieces with an intermediate tolerance and surface finish. Explain why there is a great change between 1 and 10 and a small change between 1000 and 10,000 pieces. b. Compare the costs for fit, intermediate, and rough tolerances with a volume of 100 pieces. c. Compare the costs of manufacturing the component out of various materials.arrow_forwardWhat is the purpose of a flywheel in a machine?arrow_forward
- Why should you avoid recutting or grinding parts whenever possible?arrow_forwardWhich is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?arrow_forwardExample 6.6 a)The direction of the IM (impending motion) of the Block is _____degrees. NOTE: If the author directly provides this information, enter the number of Sig Figs as the author provides. b)The direction of the IM (impending motion) of the Wedge is _____degrees. NOTE: If the author directly provides this information, enter the number of Sig Figs as the author provides. c)Consider the FBD of the Block: The magnitude of the angle that the R2 force is off the horizontal is _____degrees. NOTE: If the author directly provides this information, enter the number of Sig Figs as the author provides. d)Consider the FBD of the Block: The direction of N2 (normal force on Surface-2) is _____degrees. NOTE: If the author directly provides this information, enter the number of Sig Figs as the author provides. e)Consider the FBD of the Block: The direction of F2 (friction force on Surface-2) is _____degrees. NOTE: If the author directly provides this information, enter the number of…arrow_forward
- Tandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing stage OIt is not possible to reduce at one stage O Annealing is needed between stages Accuracy in dimensions is not possible otherwise Which of the following abrasive materials is most appropriate for grinding nonferrous metals? Silicon carbide O Aluminum oxide Cubic boron nitride Diamondarrow_forwardPlease help, answer it and show work. Thanksarrow_forwardWhat is the name of this picture?arrow_forward
- can someone briefly discuss the components of arbor press machine. thanksarrow_forwardWhy might a 50 division vernier caliper not be more advantageous, in terms of measurement accuracy, than a 10 division vernier caliper?arrow_forwardlathe machine has a constant failure rate and a mean time to failure of 10 years. What is the probability that the lathe machine will fail between 5 and 12 years after being installed?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License