DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 40, Problem 19RQ
To determine
The reason for part sitting on locator buttons and not resting on the flat plate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
what is the omega value?
as per the professor, the IC is at b not a
need answer handwritten with black pen
Give 1 example of methods of section
Chapter 40 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 40 - What are the two primary functions of a...Ch. 40 - Prob. 2RQCh. 40 - An early treatise defined a jig as a device that...Ch. 40 - Does an ordinary vise qualify as a fixture? Why or...Ch. 40 - What basic criteria should be considered in...Ch. 40 - In any part drawing, what are the critical...Ch. 40 - What difficulties can result from not keeping...Ch. 40 - Prob. 8RQCh. 40 - Which of the basic design principles relating to...Ch. 40 - What are the two reasons for not having drill...
Ch. 40 - Why does the use of down milling often make it...Ch. 40 - Prob. 12RQCh. 40 - A large assembly jig for an airplane-wing...Ch. 40 - Explain why the use of a given fixture may not be...Ch. 40 - Prob. 15RQCh. 40 - In the clamps shown in Figure 40.20, what is the...Ch. 40 - What are other common types of clamp?Ch. 40 - What is the purpose of dimensioning the...Ch. 40 - Prob. 19RQCh. 40 - In Figure 49.9. why arent there three points put...Ch. 40 - Which set of locators in Figure 49.9 establishes...Ch. 40 - What are the four stages of the SMED methodology...Ch. 40 - Prob. 23RQCh. 40 - How could the intermediate jig concept be used in...Ch. 40 - Develop a sequence of operations to produce the...Ch. 40 - Suppose in the sample problem at the end of this...Ch. 40 - Notice that the holes in the part in Figure 49.9...Ch. 40 - Prob. 6PCh. 40 - A part has two holes located for drilling by...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe four uses of the combination set.arrow_forwardThe diagram shows a stepped-cone pulley system used on some pillar drills. The belt is arranged on the four different steps of the cone pulley to obtain different speeds. The cone pulley has four steps (A, B, C & D). Another cone pulley having four steps (E, F, G and H) is placed parallel to the spindle cone pulley. Both the cone pulleys are connected by a flat or V belt. The belt can be arranged between the steps “A & H”, “B & G”, “C & F” and “D & E”. The cone pulley at the bottom is connected to the electric motor by a V-belt. (Lower pulley is the driver pulley, and the upper pulley is the driven pulley). The diameters of the pulleys are given in the following table.arrow_forwardA workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the workpiece.arrow_forward
- A programmable indexing fixture creates a fourth axis called a ________ __________ that is similar to a rotary table used on a manual milling machine.arrow_forwardHYDRAULICS & ELECTRO-HYDRAULICSarrow_forwardK/s docs.google.com/forms öslg äbäi The command using to insert * :seal is إجابتك نقطة واحدة The main part in the screw * :connection is Screw O Nut Hole Washer 3alg äbäi The command using to insert * :center line is إجابتك ...arrow_forward
- Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as; 1. Crank-rocker mechanism; 2. Drag link mechanism; 3. Double rocker mechanism; 4. Crossover-position or charge-point mechanism; 5 Triple rocker mechanism (non-grashof). Use technical Pen for the following: 0.2(light -for linkages and hand writing), 0.4(medium - for joints), 0.6(heavy - for fixed link or frames) use 2-4-4 template, all caps, italicized.arrow_forwardIf during the last operation on a part, a G1 code command is programmed but no F-value is given in the block, what feed rate will be used?arrow_forwardA workpiece requires 9 divisions. Calculate the correct direct indexing plate and number of notches to advance the plate. Plates with 24, 30, and 36 notches are available.arrow_forward
- Briefly describe the use of I and J for the arc center method of circular interpolation.arrow_forwardable to draw the sequence chart?arrow_forwardQ3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the centers of the given holes in Cartesian coordinates. The center of holes are located on the same radius and are separated by same radial distance, in other words, the shape is radially symmetric. 60.00 Ø200 Figure 2: circular disk marking.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License