(a) Explanation PSPICE Simulation: To find the Thevenin resistance R Th : Draw the circuit diagram in PSPICE as shown in Figure 1. Save the circuit and provide the Simulation Settings as shown in Figure 2. Now run the simulation and the results will be displayed as shown in Figure 3 by enabling “Enable Bias Voltage Display” icon and “Enable Bias Current Display” icon. From Figure 3, the Thevenin resistance R Th across the terminals a-b is calculated as follows, R Th = 1 V 222.2 μ A = 1 V 222.2 × 10 − 6 A { ∵ 1 μ = 10 − 6 } = 4500.45 × 10 − 3 × 10 3 Ω { ∵ 1 Ω = 1 V 1 A } = 4 (b) To determine Calculate the percentage of error in the voltmeter reading.

Electric Circuits, Student Value Edition Format: Unbound (saleable)

11th Edition

ISBN: 9780134747170

Author: NILSSON, James W.^riedel, Susan

Publisher: Prentice Hall

See similar textbooks

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysi…

Videos

Question

Chapter 4, Problem 72P

(a)

To determine

Calculate the voltmeter reading across the terminals a-b in the given circuit using PSPICE.

(b)

To determine

Calculate the percentage of error in the voltmeter reading.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 71P

Chapter 4, Problem 73P

Students have asked these similar questions

"Please, the answer must be documented from a book, experience, or accurate information without using artificial intelligence." Write an Arduino program to read the status of two push buttons connected to pins 2&3 respectively and flash ON two LED's connected to pins 12&13 respectively according to the following scenario: If pin 2 is HIGH let LED 12 flash with delay of 400ms, and if pin 3 HIGH, let LED 13 flash ON with delay of 300ms.

"Based on a source, book, or expertise in the specialized field, I need a solution to the question." Write an Arduino program code that controls the intensity of each LED (Ascending and descending) connected to pins {3, 5, 6, 9, 10, 11} successively at an array method) an interval one of one second. (Hint use

"Based on a source, book, or expertise in the specialized field, I need a solution to the question." Write an Arduino program to control water tank levels, The 1st Tank level is monitored by ultrasonic sensor No.1, connected to pin Ao on the Arduino board and it's linked to a valve via port 7 to regulate the valve's opening and closing. Similarly, 2nd tank is monitored by ultrasonic sensor No.2, connected to pin A1, and linked to a valve through port 8. Follow the rules in the Table below to control valve and motor activation via port 13 with a 500 ms delay: TRIYAH UN Water level Tank Tank 1<500 (Threshold) Tank 2<300 Tank 1==500 Tank 2<300 Tank 1<500 Tank 2==300 Tank 1=500 Tank 2=300 Motor ON ON SON OFF Valve 1 ON OFF ON OFF Valve 2 ON ON OFF OFF

Chapter 4 Solutions

Electric Circuits, Student Value Edition Format: Unbound (saleable)

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.