Explanation Given Information: The disk is the solid cylinder and angle of oscillation is small. Write the expression for the potential energy for the system. P E = 1 2 k 1 4 x 2 + δ 2 ...... (1) Here, the spring constant is k , deflection at the equilibrium state is δ , and the deflection of the system is x . For maximum potential energy, x = A and for minimum potential energy, x = 0 . Substitute A for x and P E max for P E in Equation (1). P E max = 1 2 k 1 4 A 2 + δ 2 Substitute 0 for x and P E min for P E in Equation (1). P E min = 1 2 k 1 4 0 2 + δ 2 = 1 2 k δ 2 Write the expression for the kinetic energy of the system. K E = 1 2 m 1 x ˙ 2 + 1 2 I θ ˙ 2 + 1 2 m 2 x ˙ 2 4 ...... (2) Here, the velocity of the system is x ˙ , mass of the pulley is m 2 , mass of the block is m 1 angular velocity is θ ˙ , and moment of inertia of pulley is I . Write the expression for the angular velocity. θ ˙ = x ˙ 2 R Substitute x ˙ 2 R for θ ˙ in Equation (2). K E = 1 2 m 1 x ˙ 2 + 1 2 I x ˙ 2 R 2 + 1 2 m 2 x ˙ 2 4 = 1 2 m 1 x ˙ 2 + 1 2 I x ˙ 2 4 R 2 + 1 2 m 2 x ˙ 2 4 = 1 2 m 1 + I 4 R 2 + m 2 4 x ˙ 2 Write the expression of energy balance by applying Rayleigh’s method. K E = P E max − P E min ...... (3) Substitute 1 2 k δ 2 for P E min , 1 2 k 1 4 A 2 + δ 2 for P E max , and 1 2 m 1 + I 4 R 2 + m 2 4 x ˙ 2 for K E in Equation (3)

3rd Edition

ISBN: 9780100254961

Author: Palm

Publisher: YUZU

See similar textbooks

Question

Chapter 4, Problem 4.36P

To determine

The expression for the natural frequency of the system.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 4.35P

Chapter 4, Problem 4.37P

Students have asked these similar questions

where M1=0.41m, M2=1.8m, M3=0.56m, please use bernoulis equation where necessary and The solutions should include, but not be limited to, the equations used tosolve the problems, the charts used to solve the problems, detailed working,choice of variables, the control volume considered, justification anddiscussion of results etc.If determining the friction factor, the use of both Moody chart and empiricalequations should be used to verify the validity of the value.

Q3. The attachment shown in Fig.2 is made of 1040 HR. Design the weldment (give the pattern, electrode number, type of weld, length of weld, and leg size). All dimensions in mm 120 Fig.2 12 17 b =7.5 5 kN 60 60°

15 mm DA 100 mm 50 mm Assuming the load applied P 80 kN. Determine the maximum stress in the bar shown assuming the diameter of the whole A is DA = 25 mm.

Chapter 4 Solutions

EBK SYSTEM DYNAMICS

Ch. 4 - Prob. 4.1P Ch. 4 - In the spring arrangement shown in Figure P4.2....Ch. 4 - In the arrangement shown in Figure P4.3, a cable...Ch. 4 - In the spring arrangement shown in Figure P4.4,...Ch. 4 - For the system shown in Figure P4.5, assume that...Ch. 4 - The two stepped solid cylinders in Figure P4.6...Ch. 4 - A table with four identical legs supports a...Ch. 4 - The beam shown in Figure P4.8 has been stiffened...Ch. 4 - Determine the equivalent spring constant of the...Ch. 4 - Compute the equivalent torsional spring constant...

Ch. 4 - Plot the spring force felt by the mass shown in...Ch. 4 - Calculate the expression for the natural frequency...Ch. 4 - Prob. 4.13P Ch. 4 - Obtain the expression for the natural frequency of...Ch. 4 - 4.15 A connecting rod having a mass of 3.6 kg is...Ch. 4 - Calculate the expression for the natural frequency...Ch. 4 - For each of the systems shown in Figure P4.17, the...Ch. 4 - The mass m in Figure P4.18 is attached to a rigid...Ch. 4 - In the pulley system shown in Figure P4.19, the...Ch. 4 - Prob. 4.20P Ch. 4 - Prob. 4.21P Ch. 4 - Prob. 4.22P Ch. 4 - In Figure P4.23, assume that the cylinder rolls...Ch. 4 - In Figure P4.24 when x1=x2=0 the springs are at...Ch. 4 - 4.25 In Figure P4.25 model the three shafts as...Ch. 4 - In Figure P4.26 when 1=2=0 the spring is at its...Ch. 4 - Prob. 4.27P Ch. 4 - For the system shown in Figure P4.28, suppose that...Ch. 4 - For the system shown in Figure P4.29, suppose that...Ch. 4 - Prob. 4.30P Ch. 4 - For Figure P4.31, the equilibrium position...Ch. 4 - Prob. 4.32P Ch. 4 - Prob. 4.33P Ch. 4 - 4.34 For Figure P4.34, assume that the cylinder...Ch. 4 - Use the Rayleigh method to obtain an expression...Ch. 4 - Prob. 4.36P Ch. 4 - 4.37 Determine the natural frequency of the system...Ch. 4 - Determine the natural frequency of the system...Ch. 4 - Use Rayleigh's method to calculate the expression...Ch. 4 - Prob. 4.40P Ch. 4 - Prob. 4.41P Ch. 4 - Prob. 4.42P Ch. 4 - The vibration of a motor mounted on the end of a...Ch. 4 - Prob. 4.44P Ch. 4 - Prob. 4.45P Ch. 4 - A certain cantilever beam vibrates at a frequency...Ch. 4 - Prob. 4.47P Ch. 4 - 4.48 The static deflection of a cantilever beam is...Ch. 4 - Figure P4.49 shows a winch supported by a...Ch. 4 - Prob. 4.50P Ch. 4 - Prob. 4.51P Ch. 4 - Prob. 4.52P Ch. 4 - 4.53 In Figure P4.53 a motor supplies a torque T...Ch. 4 - Derive the equation of motion for the lever system...Ch. 4 - Prob. 4.55P Ch. 4 - Figure P4.56a shows a Houdaille damper, which is a...Ch. 4 - 4.57 Refer to Figure P4.57. Determine the...Ch. 4 - For the system shown in Figure P4.58, obtain the...Ch. 4 - Find the transfer function ZsXs for the system...Ch. 4 - Prob. 4.60P Ch. 4 - Find the transfer function YsXs for the system...Ch. 4 - Prob. 4.62P Ch. 4 - 4.63 In the system shown in Figure P4.63, the...Ch. 4 - Prob. 4.64P Ch. 4 - Figure P4.65 shows a rack-and-pinion gear in which...Ch. 4 - Figure P4.66 shows a drive train with a spur-gear...Ch. 4 - Prob. 4.67P Ch. 4 - Prob. 4.68P Ch. 4 - Prob. 4.69P Ch. 4 - Figure P4.70 shows a quarter-car model that...Ch. 4 - Prob. 4.71P Ch. 4 - 4.72 Derive the equation of motion for the system...Ch. 4 - A boxcar moving at 1.3 m/s hits the shock absorber...Ch. 4 - For the systems shown in Figure P4.74, assume that...Ch. 4 - Refer to Figure P4.75a, which shows a ship’s...Ch. 4 - In this problem, we make all the same assumptions...Ch. 4 - Refer to Figure P4.79a, which shows a water tank...Ch. 4 - The “sky crane” shown on the text cover was a...Ch. 4 - Prob. 4.81P Ch. 4 - Prob. 4.82P Ch. 4 - Suppose a mass in moving with a speed 1 becomes...Ch. 4 - Consider the system shown in Figure 4.6.3. Suppose...Ch. 4 - Prob. 4.86P Ch. 4 - Figure P4.87 shows a mass m with an attached...Ch. 4 - Figure P4.88 represents a drop forging process....Ch. 4 - Refer to Figure P4.89. A mass m drops from a...Ch. 4 - Prob. 4.90P Ch. 4 - (a) Obtain the equations of motion of the system...Ch. 4 - Refer to part (a) of Problem 4.90. Use MATLAB to...Ch. 4 - Refer to Problem 4.91. Use MATLAB to obtain the...Ch. 4 - 4.94 (a) Obtain the equations of motion of the...Ch. 4 - 4.95 (a) Obtain the equations of motion of the...

Knowledge Booster