DeGarmo's Materials and Processes in Manufacturing

12th Edition

ISBN: 9781118987674

Author: J. T. Black, Ronald A. Kohser

Publisher: WILEY

See similar textbooks

Concept explainers

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easi…

Videos

Textbook Question

Chapter 36, Problem 39RQ

What is the advantage of placing the flux in the center of an electrode (flux-cored arc welding) as opposed to a coating on the outside (shielded metal arc welding)?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 36, Problem 38RQ

Chapter 36, Problem 40RQ

Students have asked these similar questions

1)a) Why is automation of the covered electrode arc source difficult?b) what properties is a metal with good resistance welding ability expected to have?c) Why is the heat transfer factor higher in arc welding processes with the consumed electrode than the methods used with the non-consumed electrode?d) Why is it important to weld thin and long instead of thick and short?e) why is it important that the source root is designed to be forced to press, not pull? 2) there is a characteristic liquid penetration error on a large piece of steel poured in the sand mold. The surface of the piece consists of a mixture of sand and metal.a) Explain at least 3 of the steps that can be taken to correct this error.b) what other types of casting errors may possibly occur in each of these steps? Explain 3) grain structure formed in part after casting;a) Describe by drawing a figure.b) what problems can this grain structure pose? Please explain. How can these problems be cured?4) explain two of the…

Select an appropriate electrode and flux of Submerged Arc Welding (SAW) process for nickel alloy steel.

8) The correct ways to control liquation cracking tendency in fusion weld joint are I. Use of filler metal that solidifies before the partially melted zone I. Use of single pass welding with higher net heat input instead of multipass welding III. Use of high energy density processes IV. Preheating the substrates V. Use of base metals with fine grain structure OI, II, and III II, and IV OII, IV, and V O II, III and IV

Chapter 36 Solutions

DeGarmo's Materials and Processes in Manufacturing

Ch. 36 - What is the principal fuel gas used in oxyfuel-gas...Ch. 36 - Why does an oxyfuel-gas welding torch usually have...Ch. 36 - What is the location of the maximum temperature in...Ch. 36 - What function or functions are performed by the...Ch. 36 - What three types of flames can be produced by...Ch. 36 - Which type of oxyfuel flame is most commonly used?Ch. 36 - What are some of the alternative fuels (other than...Ch. 36 - Why might a welder want to change the tip size (or...Ch. 36 - What is filler metal, and why might it be needed...Ch. 36 - What is the role of a welding flux?

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

In each case, explain how to find the resultant internal loading acting on the cross section at point A. Draw a...

Mechanics of Materials

The power needed to overcome wind and friction dragassociated with an automobile traveling at a constantvelocit...

Fundamentals of Heat and Mass Transfer

A loading causes the block to deform into the dashed shape. Explain how to determine the strains AB AC, BC, (A)...

Mechanics of Materials (10th Edition)

12. Consider the following strange, but true, units: 1 arroba =11.5 kilograms [kg] 1 peck = 9 liters [L] A bask...

Thinking Like an Engineer: An Active Learning Approach (3rd Edition)

the internal loading at point B.

Engineering Mechanics: Statics & Dynamics (14th Edition)

What parts are included in the vehicle chassis?

Automotive Technology: Principles, Diagnosis, and Service (5th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.